Skip to content
(920) 655-2193|Serving Green Bay & Northeast Wisconsin
Rise & Grind Concrete
Get My Price
Concrete leveling · Comparison

Foam Leveling vs. Mudjacking

Foam: about 5/8"Roughly dime-sizedMudjacking: about 1-1/2" to 2"Dashed ring = 1-1/2", solid = 2"DRAWN TO SCALE
DRAWN TO SCALEFoamabout 5/8"Roughly dime-sizedMudjackingabout 1-1/2" to 2"Dashed 1-1/2", solid 2"
The short answer

Foam lifting and mudjacking both raise sunken concrete by filling the space under it. Foam goes in through 5/8-inch holes, weighs about 2 to 5 pounds per cubic foot and is ready in about 15 minutes. Mudjacking slurry needs 1½ to 2 inch holes, weighs 100 to 150 pounds per cubic foot and needs 24 to 48 hours before cars. Mudjacking usually costs less upfront.

By Rob Diederich, owner · Updated

You got two quotes for the same sunken slab. One crew mudjacks, the other uses foam, and the numbers aren't close. Both say their way is better.

Know this up front: foam is the only lifting method we use, so if you came looking for mudjacking in Green Bay, foam is what we'd offer instead. We'll still tell you where mudjacking makes sense, because sometimes it does.

For why slabs sink and every repair option, replacement included, see how concrete lifting works. This is just the head-to-head: polyjacking vs. mudjacking.

What Each Method Pumps Under Your Slab

Every lifting method fills the empty or soft space under a slab, then keeps filling until the slab rises. The difference is what goes in.

  • Mudjacking pumps a slurry of soil or sand, cement, and water. Some mixes add lime, fly ash, or clay. It's thick, gritty, and heavy, and the pump pressure is what raises the slab. Once it sets, it's a hard, cement-like fill.
  • Stone slurry grout is a cousin of mudjacking: finely ground limestone mixed with water, sometimes with cement added.
  • Polyurethane foam, or polyjacking, starts as two liquids that mix at the injection gun. They react and expand into a rigid, closed-cell foam. The expansion is what does the lifting.

Side by side

Polyurethane foamMudjacking
MaterialTwo-part polyurethane foamCement, sand and soil or limestone slurry
Hole sizeAbout 5/8 inch, about a dimeAbout 1½–2 inches
Weight added under the slabAbout 2–5 lb per cubic footAbout 100–150 lb per cubic foot
What lifts the slabThe foam expandingPressure from the pumped slurry
StrengthAbout 64–100 psi compressive when curedDepends on the mix
Ready for vehiclesWalk on it right away, drive on it the same day; foam is at 85–90% strength in about 15 minutesUsually 24–48 hours
WaterWaterproof once cured, won't wash outCan erode where water flows under the slab
Fine controlVery fine, stops when the slab hits the lineGood, but heavier and slower to react
Patches left behindSmallLarger
Interior slabsWell suited: small holes, little messPossible, but messier
LifespanGenerally rated longer, with no single agreed numberCost guides commonly say 5–10 years when done well
National costHigher upfront: about $5–25 per sq ftUsually lower: about $3–6 per sq ft
What the fill isPetroleum-based plasticMineral-based (soil, sand, cement)
Foam figures from manufacturer data sheets (AP Lift 435, Precision Lift 475); slurry weight, hole size and cure from HD Foundation Repair; national costs from HomeAdvisor, 2026.

That last row is a fair point in mudjacking's favor. If you'd rather not have plastic in the ground, mudjacking and stone slurry are mineral fills.

Mudjacking: heavy slurryMudjackingFoam: light, waterproofFoam
3D render, simplified. Both methods lift the slab. When water gets in later, slurry can wash out and let the slab drop again; foam doesn't absorb water.

Where the Differences Actually Show Up

The holes

A dime-sized patch and a patch the size of a quarter or bigger don't look the same, especially on a front walk or a stamped or colored patio. Every hole gets patched either way, and no patch perfectly matches 20-year-old concrete. Smaller patches are just easier to live with.

The weight you're adding to soil that already failed

This is the difference we think matters most.

Say a 10-by-10-foot driveway slab has dropped, and there's an average of 2" of empty space under it. That's about 17 cubic feet to fill.

  • Mudjack slurry at roughly 100 lb per cubic foot: about 1,700 pounds of new weight sitting on the same soil.
  • Lifting foam at a few pounds per cubic foot: somewhere around 50 to 100 pounds.

Firm, dry ground may carry that extra weight fine. Loose backfill or soggy clay, usually the reason the slab sank in the first place, may not.

Washout

Spring melt and a wet April send a lot of water under slabs around here. Cured foam is closed-cell, so it doesn't soak up water and doesn't erode. A cement-based slurry is more porous, and if water keeps running under the slab, it can wear away at the fill.

Highway engineers have seen the same thing. A 2017 Missouri Department of Transportation research brief on slab stabilization reported that cement grout had been phased out there because of its erosion potential, with polyurethane now doing the job.

Neither fill stops water from eroding the soil around it, so fix the downspouts whichever method you pick.

Getting your slab back

Foam sets within minutes. You can walk on it right away and drive on it the same day. Mudjacking slurry has to set up first, and national cost guides put that at one to three days before the slab should carry real weight. For a driveway, or the only path to your front door, that counts.

Upfront cost

Mudjacking almost always quotes lower. National cost guides updated in 2026 put mudjacking at roughly $3–$6 per square foot and foam at $5–$25, a much wider spread. The fill is the big reason. Soil, sand, and cement are cheap. Lifting foam isn't.

The gap can grow on a big washout under a big slab, where material becomes a larger share of a foam quote. If the ground is dry and stable and price matters most, that's a legitimate reason to choose mudjacking.

Longevity

Most longevity claims come from someone selling one method. Cost guides commonly give mudjacking 5–10 years when done well and credit foam with lasting longer, without agreeing on a number. Either way, the fill is rarely what gives out first. The soil under it moves, and water is almost always what moves it.

Where foam wins

  • On soils that already failed. Heavy slurry adds load to the same weak soil that caused the problem; foam barely adds any.
  • Where water is the cause. Foam doesn't wash out the way slurry and soil can.
  • Where looks matter. Small holes on a front walk or patio are far less noticeable.
  • When you need it back fast, like a driveway or a business entrance.

When mudjacking can make sense

Mudjacking is a legitimate method. If you're filling a very large void under a slab that won't see much water, and budget is the deciding factor, slurry can be the cheaper way to do it. Ask any contractor what material they're using and what the warranty covers; a vague answer is a warning sign.

On dry, stable ground, mudjacking can do the job; next to foundations, over soft or wet clay, under AC pads, and inside garages, foam is usually worth the extra money. If you came here looking for a mudjacking contractor, mudjacking in Green Bay covers what to ask one and what we do instead.

Wisconsin Conditions That Tip the Scale

  • Slow-draining clay. Much of the Green Bay area sits on clay and silt laid down in old glacial lakes. It holds water and drains slowly, so the ground under a slab stays wet long after every rain and thaw. A light fill that doesn't mind water counts for more here.
  • Loose backfill along the house. Stoops, patios, walks, and AC pads next to the foundation sit on soil that was pushed back in after the basement was dug. It's the softest ground on most lots, and the worst place to stack heavy fill.
  • Spring melt. A winter's worth of snow melting at once soaks that backfill. That's why so many sunken slabs show up in April and May.
  • Frost. Wet, fine-grained soil heaves when it freezes, and neither method stops that. A slab that only looks off in late winter may be frost-heaved, not sunk, and nobody should lift it until the ground thaws. Our concrete leveling season runs from spring thaw to freeze-up.
  • Road salt. Salt flakes the surface but has nothing to do with sinking, and neither method fixes it. A penetrating sealer helps protect concrete that's still sound, which is a separate job we also do.

Which One Fits Your Situation?

Your situationBetter fitWhy
Sidewalk square out by the street, firm dry ground, lowest price winsMudjacking is reasonableWeight and washout matter less on stable soil
Patio, stoop, or walk right against the foundationFoamLight fill on the loosest soil on the lot
AC or heat pump padFoamSmall holes, light fill, and little mess around the equipment (see our AC pad guide)
Garage floor or other interior slabFoamSmall holes and no gritty slurry inside the building
Slab where a downspout or sump line was dumpingFoam, after you move the waterA fill that won't wash out, in the spot water already proved it can reach
Driveway you need to park on tonightFoamDrive on it the same day
Stamped, colored, or exposed-aggregate concreteFoamSmaller patches where patches show the most
Slab that was mudjacked before and sank againUsually foamAdds very little weight on top of what's already down there
Large washout under a big slab, firm ground, tight budgetGet quotes for bothMaterial cost can make mudjacking much cheaper here
Slab broken into pieces, crumbling, or pushed up by tree rootsNeitherNo lifting method fixes these. See is concrete lifting worth it

Where Stone Slurry Fits

Stone slurry grout sits in the middle. Its holes are about 1" across, smaller than mudjacking and bigger than foam, and it's a mineral fill, which suits people who'd rather skip plastic. It's still a heavy, water-based mix, and when the blend is light on cement, water can erode the limestone over time. Set time depends on the mix, so ask before you plan to park on it.

Can foam go where mudjacking was done before?

Usually, yes. If a slab was mudjacked years ago and has settled again, foam can be injected around or through the old material. The old large holes get patched too.

Comparing Two Quotes? Make Them Apples to Apples

Before you compare prices, check:

  • Same slabs, same goal. Are both lifting the same squares to the same finished height and slope?
  • What's underground. Did they ask about buried downspout lines, sump discharge, and drain pipes? Any fill pumped under a slab will follow an open pipe.
  • Joint sealing. Is caulking the joints and cracks included? Sealing keeps water from getting back under the slab, whatever fill is down there.
  • The cause. Did they tell you what sank it and what to fix? If not, you'll be doing this again no matter which method you pick.
  • What happens if it settles again. Ask whether there's a written warranty and what conditions come with it.

For vetting the contractor itself, see how to choose a concrete contractor.

Sources

  1. Alchemy-Spetec AP Lift 435 technical data sheet (lifting foam)
  2. Prime Resins Precision Lift 475 technical data sheet (lifting foam)
  3. HD Foundation Repair: mudjacking vs. polyurethane foam
  4. HomeAdvisor: concrete leveling and mudjacking cost (updated June 2026)
Questions

Common questions

Which lasts longer, foam or mudjacking?

Foam generally lasts longer. Polyurethane doesn't absorb water or wash out, and it adds very little weight to the soil. Mudjacking slurry is heavy and can erode where water flows under the slab, which is why mudjacked slabs sometimes settle again.

Which costs less, foam or mudjacking?

Mudjacking is usually cheaper upfront: national cost guides put it at about $3 to $6 per square foot, against about $5 to $25 for foam. Foam needs smaller holes, adds far less weight to the soil and doesn't wash out, so over the life of the slab the cost is often similar or lower.

Why are foam holes smaller than mudjacking holes?

Foam goes in as a thin liquid and expands after it's under the slab, so it fits through a 5/8-inch port. Mudjacking slurry is thick and has to be pumped through holes around 1-1/2 to 2 inches wide.

Does mudjacking wash out?

It can. Slurry is cement mixed with sand or soil, and where water runs under the slab it can erode over time. That's one of the common reasons mudjacked slabs drop again.

Is polyjacking the same thing as foam lifting?

Yes. Polyjacking, poly leveling, foam lifting, and foam jacking all mean raising concrete with injected polyurethane foam. Mudjacking is the slurry version, and slabjacking is a general term that can mean either.

Why does mudjacking cost less?

Mostly the material. Soil, sand, and cement cost a fraction of what lifting foam does, so the more fill a job needs, the wider the price gap gets.

Is mudjacking outdated?

No. It's the older method, but it still works, and on dry, stable ground without a water problem it can hold up well. Its weak spots are weight and water, which is why it struggles most on soft or wet soil.

Can you foam lift a slab that was mudjacked before?

Usually, yes. Foam goes in through new, small holes and fills whatever space has opened up under the slab since the first lift. The old, larger patches will still be visible.

Why are mudjacking holes so much bigger?

The slurry is thick and gritty, so it needs a bigger opening to pump through. Foam goes in as a thin liquid and expands once it's under the slab, so a 5/8" hole is plenty.

Do you offer mudjacking?

No. Foam is the only lifting method we use. If your slab sits on firm, dry ground and mudjacking would serve you just as well for less money, we'll tell you that.

Keep reading

Related

Mudjacking · Green Bay
Mudjacking in Green Bay

Looking for mudjacking in Green Bay? We do polyurethane foam lifting instead: smaller holes, lighter fill, won't wash out, same-day use. See how it compares.

Concrete leveling · The process
How Foam Lifting Works

How foam concrete lifting works, with the numbers: 5/8-inch holes 3–4 ft apart, foam at 90% strength in 15 minutes, 1–4 hours on site, same-day use.

Concrete leveling · Decision guide
Lift or Replace?

Lift or replace sunken concrete? When each makes sense, with Green Bay costs ($4–$10/sq ft to lift vs. about $9–$20 to replace a driveway) and a quick checker.

Pricing · Concrete leveling
Concrete Leveling Cost

Concrete leveling cost in Green Bay: our foam lifting prices by job, from a $300 minimum, next to national averages, and what moves the price.

Learn · Concrete Lifting
How Does Concrete Lifting Work?

How concrete lifting works, step by step: why slabs sink around Green Bay, foam vs. mudjacking vs. stone slurry vs. replacement, what a lift costs, and what lifting can't fix.

Learn · Concrete Lifting
Is Concrete Lifting Worth It?

Foam concrete lifting in Green Bay is fast and costs about half of replacement on average, but it has real limits. Honest pros, cons, and a lift-or-replace table.

Not Sure Which Method Fits? Send Photos. No Sales Call.

Send a wide photo of the slab, a close-up of the worst edge with a tape measure standing next to it, and a shot of the nearest downspout. We'll tell you whether foam is the right fit and what it costs, or whether a cheaper method would do the job on your slab.

Get My PriceCall (920) 655-2193

Or see why we offer foam lifting as a mudjacking alternative →.