Skip to content
(920) 655-2193|Serving Green Bay & Northeast Wisconsin
Rise & Grind Concrete
Get My Price
Questions

Frequently asked questions

383 questions, sorted by service. Search them, or open a group and tap a question for the short answer and a link to the page that covers it in full.

Type a word or two and the list narrows as you type.

Concrete lifting & leveling

How foam lifting works, how long it lasts, what it can't fix, and how it compares with mudjacking and replacement.

Concrete lifting & leveling →Mudjacking in Green Bay →

Show Hide 59 questions from 5 pages

Concrete Leveling →

Is concrete leveling the same as concrete lifting or polyjacking?

Yes. Concrete leveling, lifting, raising, slab jacking, polyjacking and foam jacking all describe raising an existing slab back into place. Polyjacking specifically means doing it with polyurethane foam, which is what we use. Mudjacking is the older method using a cement slurry.

Full answer on Concrete Leveling →Link to this answer

How does polyurethane foam lift concrete?

Two liquid components are mixed at the gun and injected under the slab. The mix expands into a rigid foam that first fills the empty voids and then pushes up on the slab. We inject in short shots and watch a level or string line so the slab rises to the right height and stops.

Full answer on Concrete Leveling →Link to this answer

How long does foam concrete leveling last?

The foam itself does not rot, wash out or break down in wet soil, so a lift typically lasts as long as the concrete does. What can cause new movement is the soil below the foam continuing to settle or water undermining the edges, which is why we seal joints and point out drainage problems.

Full answer on Concrete Leveling →Link to this answer

Can concrete sink again after it's lifted?

It can, but it's uncommon when the cause is handled. Foam weighs only a few pounds per cubic foot, so it doesn't add load to weak soil the way a heavy slurry does. Sealing joints and moving downspouts away from slabs removes the most common cause of repeat settling. If a slab keeps dropping after a proper lift, the soil is failing deeper than foam under the slab can reach, and we'd tell you that rather than lift it a third time.

Full answer on Concrete Leveling →Link to this answer

How soon can I walk or drive on lifted concrete?

The foam reaches 85 to 90% of its full strength in about 15 minutes. You can walk on the slab as soon as we pack up, and drive on it the same day, once the cement grout in the holes has set.

Full answer on Concrete Leveling →Link to this answer

How big are the holes and what do they look like after?

The holes are about 5/8 inch across, roughly the size of a dime. They're filled with cement grout and finished flush. On new concrete they blend in well; on weathered concrete the patches can be a shade lighter at first.

Full answer on Concrete Leveling →Link to this answer

Can you lift cracked concrete?

Usually, yes. A slab cracked into a few large pieces can be lifted piece by piece and the cracks sealed afterward. A slab broken into many small pieces can't be raised as one surface and is better replaced.

Full answer on Concrete Leveling →Link to this answer

How high can you lift a slab?

Most lifts are between one and four inches. Larger lifts are often possible when the slab is intact and there's room for it to move, and we judge those from your photos.

Full answer on Concrete Leveling →Link to this answer

Is the foam safe for kids, pets, my lawn and the groundwater?

Yes. Once cured, which takes minutes, the foam is an inert, closed-cell plastic that doesn't dissolve, leach or break down in wet soil, so it doesn't affect your lawn, garden or well. During the injection we ask that kids and pets stay inside or away from the work area, and we clean up any overspray before we leave.

Full answer on Concrete Leveling →Link to this answer

Do I need to be home during the work?

No. Our rig carries its own power and material, so we don't need to get into the house. We just need the concrete clear of cars and furniture and a way to reach it. We'll text when we start and when we're done.

Full answer on Concrete Leveling →Link to this answer

Can you level concrete in the winter in Wisconsin?

We lift from the spring thaw until the ground freezes. Once the soil under the slab is frozen solid, lifting isn't reliable because the frozen ground moves again when it thaws. Photos sent in winter get a price and a spot on the spring schedule.

Full answer on Concrete Leveling →Link to this answer

How far apart are the injection holes?

About 3 to 4 feet apart in a grid, kept off the edges and corners where concrete is weakest. A typical 10 by 10 foot section gets 6 to 10 holes, each 5/8 inch across. Spreading the holes out lets the slab rise evenly instead of tipping.

Full answer on Concrete Leveling →Link to this answer

What is the lifting foam made of?

Two liquids, an isocyanate and a polyol resin blend, are mixed at the gun and react under the slab into rigid polyurethane foam. Lifting foams cure to about 2 to 5 pounds per cubic foot with roughly 64 to 100 psi of compressive strength, depending on the product.

Full answer on Concrete Leveling →Link to this answer

Can foam stabilize a slab that hasn't sunk yet?

Yes. A slab that sounds hollow, rocks when you step on it or shows a gap under its edge has a void beneath it and will drop eventually. Filling that void with foam before it settles is called stabilization or void filling: same holes, same foam, just no lift. It costs less than lifting the slab later and sealing the cracks it picks up on the way down.

Full answer on Concrete Leveling →Link to this answer

What should I ask a concrete leveling company before hiring one?

Four things. What goes under the slab, polyurethane foam or cement slurry, and what it weighs. Whether the quote is a firm price for the job, and what happens if the void under the slab turns out much bigger than expected. What the written warranty covers and for how long. And whether joint sealing is included, since open joints are what let the slab sink. Then ask for proof of insurance. We answer all of that on the quote.

Full answer on Concrete Leveling →Link to this answer

How much does it cost to lift and level a sunken concrete slab in Green Bay?

Lifting and leveling a sunken concrete slab usually costs $300 to $600 for a single sidewalk panel, AC pad or small stoop, and $300 is our lifting minimum. A garage apron or one driveway section runs $400 to $1,000, a patio of one or two slabs $600 to $1,500, and bigger jobs about $4 to $10 per square foot. A slab over a big washout can run higher, and we'll say so from your photos.

Full answer on Concrete Leveling →Link to this answer

Do you need to come out before you can give me a quote?

Usually not. Clear photos with a tape measure in the shot tell us most of what we need for a price. We still do a full walk-around before any lift, to make sure raising the slab won't damage anything built or repaired to match it after it sank, like siding, a porch roof or a deck. If your photos show something like that, we'll come out and look before we quote.

Full answer on Concrete Leveling →Link to this answer

Do I need to be home during the lift?

Not the whole time. It helps if you're there at the start for the walk-around. We check the slabs and everything touching them, so nothing gets damaged as the concrete comes up, and confirm the plan with you. After that, you can go about your day.

Full answer on Concrete Leveling →Link to this answer

Will it be loud or messy?

Drilling is loud for a few minutes. Injection is mostly the hum of the equipment. When we leave, you'll have a few small patches and a clean slab.

Full answer on Concrete Leveling →Link to this answer

Can you seal my joints and cracks while you're there?

Yes. Joint and crack caulking pairs well with a lift, because it keeps water from getting back under the slab. Ask for it when you request your quote.

Full answer on Concrete Leveling →Link to this answer

What if you find something unexpected once you start?

We stop and talk to you. If a slab won't move without risking a crack, or we find a buried pipe where we planned to drill, we'll explain what we found and what your options are before we go any further. The same goes for a much bigger void under the slab than expected: there's usually a larger problem behind a void like that, so we stop and go over it with you first.

Full answer on Concrete Leveling →Link to this answer

When can I park on it?

The same day. We'll give you the exact go-ahead before we pack up.

Full answer on Concrete Leveling →Link to this answer

How Foam Lifting Works →

How long does concrete lifting take?

Most residential jobs take a few hours from setup to cleanup. A single walkway section can take under an hour, while a full driveway with sealing can take most of a day.

Full answer on How Foam Lifting Works →Link to this answer

Is concrete lifting messy?

Not very. The holes are small, the dust is vacuumed up, and the material goes under the slab. We clean the surface and haul away our debris before we leave.

Full answer on How Foam Lifting Works →Link to this answer

Will there be trucks or heavy equipment on my lawn?

No. The rig stays on the street or your driveway, and the only things that reach the concrete are a hose and the technician. There's no skid steer, no concrete truck and no excavator, so the lawn, landscaping and sprinkler lines next to the slab stay the way they were. Mark sprinkler heads and dog-fence wires near the concrete before we arrive.

Full answer on How Foam Lifting Works →Link to this answer

How are the holes filled, and will the patches pop out in winter?

The foam itself fills the bottom of each hole as it's injected, and the top is packed with non-shrink cement grout finished flush with the surface. Because the hole is solid foam underneath rather than a hollow plug, there's nothing for frost to push up on, and the patch stays put. On older concrete the patches start a shade lighter and weather in over a season.

Full answer on How Foam Lifting Works →Link to this answer

What if there's a large void under my slab?

The foam fills it first. Big voids take more material, which is why we ask for a photo of any gap you can see at the slab edge; it's the one thing that moves a price. Lifting foam goes in on roughly a 3-foot grid, in short shots so each one firms up before the next. If a void is big enough that the soil itself is failing, deeper soil stabilization with a thinner foam on a tighter grid is a separate specialty, and we'll say so rather than pump lifting foam into a hole that keeps growing.

Full answer on How Foam Lifting Works →Link to this answer

Will lifting crack my concrete?

Lifting slowly from several holes keeps stress low, but a slab that is already weak can crack further as it moves. We point out risky slabs from the photos before we start.

Full answer on How Foam Lifting Works →Link to this answer

What if a slab gets lifted too high?

Foam can't be pulled back out once it's under the slab, so the answer is not overshooting. We inject in short shots, move between holes and watch a laser or string line the whole time, which keeps each section within about ¼ inch of its target.

Full answer on How Foam Lifting Works →Link to this answer

Foam vs. Mudjacking →

Which lasts longer, foam or mudjacking?

Foam generally lasts longer. Polyurethane doesn't absorb water or wash out, and it adds very little weight to the soil. Mudjacking slurry is heavy and can erode where water flows under the slab, which is why mudjacked slabs sometimes settle again.

Full answer on Foam vs. Mudjacking →Link to this answer

Which costs less, foam or mudjacking?

Mudjacking is usually cheaper upfront: national cost guides put it at about $3 to $6 per square foot, against about $5 to $25 for foam. Foam needs smaller holes, adds far less weight to the soil and doesn't wash out, so over the life of the slab the cost is often similar or lower.

Full answer on Foam vs. Mudjacking →Link to this answer

Why are foam holes smaller than mudjacking holes?

Foam goes in as a thin liquid and expands after it's under the slab, so it fits through a 5/8-inch port. Mudjacking slurry is thick and has to be pumped through holes around 1-1/2 to 2 inches wide.

Full answer on Foam vs. Mudjacking →Link to this answer

Does mudjacking wash out?

It can. Slurry is cement mixed with sand or soil, and where water runs under the slab it can erode over time. That's one of the common reasons mudjacked slabs drop again.

Full answer on Foam vs. Mudjacking →Link to this answer

Is polyjacking the same thing as foam lifting?

Yes. Polyjacking, poly leveling, foam lifting, and foam jacking all mean raising concrete with injected polyurethane foam. Mudjacking is the slurry version, and slabjacking is a general term that can mean either.

Full answer on Foam vs. Mudjacking →Link to this answer

Why does mudjacking cost less?

Mostly the material. Soil, sand, and cement cost a fraction of what lifting foam does, so the more fill a job needs, the wider the price gap gets.

Full answer on Foam vs. Mudjacking →Link to this answer

Is mudjacking outdated?

No. It's the older method, but it still works, and on dry, stable ground without a water problem it can hold up well. Its weak spots are weight and water, which is why it struggles most on soft or wet soil.

Full answer on Foam vs. Mudjacking →Link to this answer

Can you foam lift a slab that was mudjacked before?

Usually, yes. Foam goes in through new, small holes and fills whatever space has opened up under the slab since the first lift. The old, larger patches will still be visible.

Full answer on Foam vs. Mudjacking →Link to this answer

Why are mudjacking holes so much bigger?

The slurry is thick and gritty, so it needs a bigger opening to pump through. Foam goes in as a thin liquid and expands once it's under the slab, so a 5/8" hole is plenty.

Full answer on Foam vs. Mudjacking →Link to this answer

Do you offer mudjacking?

No. Foam is the only lifting method we use. If your slab sits on firm, dry ground and mudjacking would serve you just as well for less money, we'll tell you that.

Full answer on Foam vs. Mudjacking →Link to this answer

Lift or Replace? →

When is concrete too far gone to lift?

When it's broken into many small pieces, when tree roots have pushed it up, or when the surface is crumbling badly enough that you'd want new concrete anyway. Otherwise, lifting is usually the better value.

Full answer on Lift or Replace? →Link to this answer

Can you lift asphalt, pavers or gravel?

No. Foam lifting works on poured concrete slabs, which are rigid enough to rise as one piece. Asphalt flexes and would crack over the injection points. Pavers aren't a slab; a sunken paver patch is lifted out, the base re-leveled and the pavers re-set. Gravel is simply regraded. If you're not sure what you have, send a photo.

Full answer on Lift or Replace? →Link to this answer

How cracked is too cracked to lift?

A slab with a crack or two, cracked into a few large pieces, can be lifted piece by piece and sealed. A slab shattered into many small pieces can't be raised as one surface and should be replaced.

Full answer on Lift or Replace? →Link to this answer

Is lifting concrete worth it if I'm selling my house?

Often, yes. Uneven walks, trip hazards and a patio pitched toward the house are easy things for a buyer's inspector to flag. Lifting fixes them in a few hours, usually for less than replacement.

Full answer on Lift or Replace? →Link to this answer

How much does replacement cost compared to lifting?

Around Green Bay, tearing out and repouring a driveway runs about $9 to $20 per square foot with tear-out. That's our estimate of the local range for tear-out and repour, from Green Bay contractor pricing we checked in November 2026; not a quote for your job. Our foam lifting averages $4 to $10, about half on average, though a lift at the top of our range can cost as much as a low-end replacement. Nationally, replacing a 100-square-foot sidewalk runs about $1,300 to $2,600, against $5 to $25 per square foot for foam lifting (HomeAdvisor, 2026). Replacement also means several days of work plus about a week before you can drive on it.

Full answer on Lift or Replace? →Link to this answer

Mudjacking in Green Bay →

Do you do mudjacking in Green Bay?

We lift sunken concrete with polyurethane foam rather than mud slurry. It's the same job, raising a slab by filling the space under it, done through smaller holes with a material that weighs far less and doesn't wash out.

Full answer on Mudjacking in Green Bay →Link to this answer

Is polyjacking the same as mudjacking?

Same goal, different material. Polyjacking uses expanding polyurethane foam through holes about 5/8 inch wide; mudjacking pumps a cement-and-soil slurry through holes about 1½ to 2 inches wide.

Full answer on Mudjacking in Green Bay →Link to this answer

Can foam lift a slab that was mudjacked before?

Usually, yes. Foam can be injected around or through the old slurry, and the old large holes get patched. If the slab sank again because water is getting under it, we'll point out the downspout or open joint that's doing it.

Full answer on Mudjacking in Green Bay →Link to this answer

What is mudjacking?

Mudjacking is the older way to raise sunken concrete. Holes about 1½ to 2 inches wide are drilled through the slab, and a slurry of soil or sand, cement and water is pumped underneath until the pressure lifts it. We do the same job with polyurethane foam, which goes in through 5/8-inch holes and lifts by expanding.

Full answer on Mudjacking in Green Bay →Link to this answer

How much does mudjacking cost in Green Bay?

We don't mudjack, but national cost guides put it at about $3 to $6 per square foot. Our foam lifting has a $300 job minimum: a single sidewalk panel or small stoop runs $300 to $600, a garage apron or one driveway section $400 to $1,000, and larger jobs about $4 to $10 per square foot.

Full answer on Mudjacking in Green Bay →Link to this answer

My quote says slabjacking. How do I know if that means mud or foam?

Ask, and look at the hole size: slabjacking is a general term that can mean either method. A cement-and-soil slurry needs holes about 1½ to 2 inches wide, while foam goes in through holes about 5/8 inch wide. While you're asking, find out what the fill weighs, whether the quote is a firm price for the job, and what the written warranty covers.

Full answer on Mudjacking in Green Bay →Link to this answer

Does the weight of mudjacking slurry really matter?

On soft ground, yes. A 10-by-10-foot slab with 2 inches of empty space under it takes about 17 cubic feet of fill: roughly 1,700 pounds of slurry at about 100 pounds per cubic foot, or around 50 to 100 pounds of foam. That weight lands on the soil that already let the slab sink, as our foam vs. mudjacking guide explains.

Full answer on Mudjacking in Green Bay →Link to this answer

Do I have to keep my car off the driveway for two days, like with mudjacking?

No. Mudjacked slabs usually need 24 to 48 hours before cars. Foam reaches 85 to 90 percent of its strength in about 15 minutes, so you can walk on the slab as soon as we pack up and drive on it the same day, once the hole patches have set.

Full answer on Mudjacking in Green Bay →Link to this answer

Will foam wash out the way mudjacking can?

No. Cured foam is closed-cell, so it doesn't soak up water or erode the way a cement-and-soil slurry can when water keeps running under a slab. Water can still wash out the soil around any fill, though, so seal the joints and move downspouts away from the slab whatever is underneath.

Full answer on Mudjacking in Green Bay →Link to this answer

Why did my mudjacked slab sink again?

Usually water. Rain or snowmelt getting under the slab through an open joint, or from a downspout dumping beside it, can erode the slurry and the soil around it, and the heavy fill adds load to soil that was already soft. We'll point out the likely source on your photos, lift the slab with foam, and seal the joints.

Full answer on Mudjacking in Green Bay →Link to this answer

How can I tell if my slab was mudjacked before?

Look for round patches about 1½ to 2 inches across, usually several per slab and often a different shade than the concrete around them. Foam lifting leaves smaller patches, about 5/8 inch. If you're not sure, send a close-up with a tape measure for scale and we'll tell you what we see.

Full answer on Mudjacking in Green Bay →Link to this answer

Do you drill new holes or reuse the old mudjacking holes?

New ones: we drill our own 5/8-inch holes, about 3 to 4 feet apart, wherever the foam needs to go. Old mudjacking holes that have loosened or opened up get patched while we're there. Sound old patches stay as they are and will still show.

Full answer on Mudjacking in Green Bay →Link to this answer

Can mudjacking be done inside a garage or basement?

It's possible, but it's messy: big holes, slurry hoses and gritty fill inside the building. Foam suits interior slabs better, with 5/8-inch holes, little mess and a floor that's back in use the same day. Before we drill indoors, we need to know about floor drains and any in-floor heat.

Full answer on Mudjacking in Green Bay →Link to this answer

Can you compare your price with a mudjacking quote I already have?

Yes. Send it with your photos and you'll get a firm foam price for the same slabs, lifted to the same height, by text within 24 hours. Check that both quotes include joint sealing, and if mudjacking would serve your slab just as well for less, we'll say so.

Full answer on Mudjacking in Green Bay →Link to this answer

Do you warranty a lift on a slab that was mudjacked before?

Yes, every lift does, old mudjacked slabs included: the written warranty on your quote spells out what's covered before you approve anything. If water is still getting under the slab, we'll point out what to fix so the lift has the best chance of staying put.

Full answer on Mudjacking in Green Bay →Link to this answer

Lifting by surface

Driveways, garage aprons, sidewalks, patios, steps, porches, pool decks, garage floors and other slabs: the questions each one raises.

Everything we lift →

Show Hide 150 questions from 10 pages

Driveway Leveling →

Can you level a driveway instead of replacing it?

Usually, yes. If the driveway slabs are still in one piece or a few large pieces and they sank and tree roots didn't push them up, they can be lifted back to level with foam, on average for about half the cost of tearing out and pouring new concrete.

Full answer on Driveway Leveling →Link to this answer

Why is water pooling on my driveway?

Pooling almost always means a section has sunk and now forms a low spot, or a slab has tipped so it drains the wrong way. Lifting that section back to its original pitch lets the water run off again.

Full answer on Driveway Leveling →Link to this answer

Will lifting fix the cracks in my driveway?

Lifting closes up height differences at cracks and joints, but it doesn't erase the crack itself. After lifting we seal the cracks with a flexible sealant so water can't get under the slab through them.

Full answer on Driveway Leveling →Link to this answer

Can you lift the driveway where it meets the street?

Usually. The approach at the curb is often in the public right-of-way, so city rules can apply. We check that first, then lift it like any other section.

Full answer on Driveway Leveling →Link to this answer

Can you lift a two- or three-car driveway?

Yes. Size doesn't change the method, only the count: a wide driveway is more sections, each lifted through its own holes to the same line. Because travel and setup are fixed, a big driveway costs less per section than a small one, and most are still done in 2 to 4 hours.

Full answer on Driveway Leveling →Link to this answer

How thick is a concrete driveway?

Most residential driveways are 4 inches thick, which carries cars and SUVs. Driveways built for heavy trucks or RVs are usually 5 to 6 inches, and the apron is often thicker than the rest of the drive. Thickness changes how much a slab weighs, not whether foam can lift it.

Full answer on Driveway Leveling →Link to this answer

How much does a driveway slab weigh?

Concrete weighs about 145 pounds per cubic foot, so a 10 by 10 foot section 4 inches thick weighs about 4,800 pounds. Spread across its underside that's only about a third of a pound per square inch, which is why expanding foam can raise it and cured foam, rated at roughly 64 to 100 psi, holds it with a wide margin.

Full answer on Driveway Leveling →Link to this answer

How much does it cost to level a sunken driveway in Green Bay?

Usually $400 to $1,000 for one sunken section, and $800 to $3,000 for two or three sections (200 to 300 square feet). Bigger driveway jobs run about $4 to $10 per square foot, with a $300 job minimum. A section sitting over a big washout can run higher, and we'll say so from your photos.

Full answer on Driveway Leveling →Link to this answer

How much cheaper is driveway leveling than a new driveway?

On average, lifting costs about half of tearing out and replacing. Lifting two or three sunken sections runs $800 to $3,000 with us. Tearing out and repouring the same 200 to 300 square feet runs about $1,800 to $6,000, at $9 to $20 per square foot: our estimate of the local range for tear-out and repour, from Green Bay contractor pricing we checked in November 2026, not a quote for your job. The ranges overlap, so a section over a big void, at the top of our range, can cost as much as a low-end replacement. New concrete also needs about a week before you can drive on it.

Full answer on Driveway Leveling →Link to this answer

Where do I park while you lift my driveway?

On the street or a neighbor's driveway for the 2 to 4 hours we're there. Cars need to be off the sections we're lifting, so pull yours out of the garage first if you'll need it. You can drive on it again the same day, once the hole patches have set.

Full answer on Driveway Leveling →Link to this answer

Can I park an RV or a heavy pickup on a lifted driveway?

As far as the foam goes, yes. Cured lifting foam is rated at roughly 64 to 100 psi, far more than a parked RV presses down once the slab spreads its weight. The limit is the concrete: a 4-inch driveway is built for cars and SUVs, while heavy trucks and RVs call for 5 to 6 inches, lifted or not.

Full answer on Driveway Leveling →Link to this answer

My car scrapes pulling into the garage. Will lifting the driveway fix it?

Usually, if it started after a section near the garage dropped. A sunken section puts a sharp break in the slope where a bumper or the underside of the car catches, and lifting it back to an even pitch takes that break out. If the driveway was simply poured that steep, lifting won't change the original grade, and we'll tell you so from the photos.

Full answer on Driveway Leveling →Link to this answer

Can you lift a heated driveway with snow-melt lines in it?

Often, but tell us before we quote. We never drill a heated slab blind: we locate the tubing before drilling or pick hole spots that stay clear of it, and layout drawings or photos from the pour help. If the lines can't be located well enough to drill safely, we'll say so rather than risk a leak.

Full answer on Driveway Leveling →Link to this answer

What photos do you need to price my driveway?

Three: a wide shot of the whole driveway with the garage in it, a tape measure standing at the lowest edge next to the section that didn't move, and one looking down the length of the slab. Add close-ups of cracks and where the downspouts empty. The measuring guide shows each shot, and we text a firm price within 24 hours.

Full answer on Driveway Leveling →Link to this answer

Is driveway leveling covered by a warranty?

Yes. Every lift comes with a written warranty, and the written warranty on your quote spells out what's covered before you approve anything. If a lifted section moves, text us a photo with a tape measure at the joint and we'll take a look. Sealed joints and downspouts that empty away from the driveway do the most to keep it level.

Full answer on Driveway Leveling →Link to this answer

Garage Apron Repair →

Why is there a drop between my garage and driveway?

The garage floor rests on the foundation, but the driveway apron rests on backfill from when the house was built. That fill compacts and washes out over time, so the apron sinks while the garage floor stays where it is.

Full answer on Garage Apron Repair →Link to this answer

Can a sunken garage apron be raised?

Yes, as long as the apron slab is still in one piece or a few big pieces. Foam is injected under it to bring it back flush with the garage floor and pitched away from the door.

Full answer on Garage Apron Repair →Link to this answer

Will my garage door seal properly after the apron is lifted?

In most cases, yes. Once the apron is back up to the garage floor, the bottom seal of the door meets the concrete again. If the seal itself is worn, replacing it is a cheap fix we can point out.

Full answer on Garage Apron Repair →Link to this answer

How do I stop water from getting under my garage slab?

Keep the apron pitched away from the door, seal the joint between the apron and the garage floor, and make sure downspouts near the garage discharge away from the driveway.

Full answer on Garage Apron Repair →Link to this answer

Why do garage aprons sink in newer homes?

The apron sits on the soil that was dug out for the basement and pushed back in. That backfill keeps settling for years after the house is built, and roof and driveway water soaks into it, so the apron is often the first slab to drop, sometimes within the first few years.

Full answer on Garage Apron Repair →Link to this answer

Is a small drop at the garage door worth fixing?

Usually, yes. Even an inch can send rain and meltwater back toward the door and into the joint, and that water keeps washing out the backfill under the apron, so the drop tends to grow each spring. A small drop is also the cheapest one to fix, because a small void takes less foam to fill.

Full answer on Garage Apron Repair →Link to this answer

How can I tell if the apron sank or the garage floor did?

Lay a straight board or level across the door line. If the step down is right at the door and the floor inside runs straight out to it, the apron sank. If the floor itself dips in its last few feet before the door, its edge settled too. Then we lift the floor first and set the apron to meet it, in the same visit.

Full answer on Garage Apron Repair →Link to this answer

Will lifting the apron keep my garage door from freezing to the concrete?

Usually, if a sunken apron is why water collects there. A door freezes down when slush and meltwater pool against its bottom seal and refreeze overnight. Lifting the apron flush with the garage floor and pitched away from the door lets that water drain off, and sealing the joint at the door keeps it from soaking in underneath.

Full answer on Garage Apron Repair →Link to this answer

Will lifting the apron stop my snowblower and plow from catching at the garage?

Yes. The lip at the door is what a plow blade or a snowblower's scraper bar hits. Once the apron is flush with the garage floor, there's no edge left to catch. The sealant in the joint at the door is finished slightly below the surface, so blades ride over it instead of peeling it out.

Full answer on Garage Apron Repair →Link to this answer

Will lifting the apron leave a bump where it meets the rest of the driveway?

No. We set the apron on a line from the garage floor down to the driveway section below it, so it ends up flush at the door, flush at its outer joint, and pitched away from the garage. If that next section dropped too, we lift it on the same visit and the same quote, so the whole run drains toward the street.

Full answer on Garage Apron Repair →Link to this answer

The apron in front of my garage is flaking. Can it still be lifted?

Usually, yes. Flaking from road salt and freeze-thaw is a surface problem, and if the slab under it is solid and in one or a few large pieces, it lifts like any other apron. Lifting won't restore the flaked surface, though. If the concrete is crumbling deep or broken into many pieces, replacement is the better call, and we'll say so from your photos.

Full answer on Garage Apron Repair →Link to this answer

How long will my garage be blocked while you lift the apron?

About 2 hours. Pull your cars out before we start if you'll need them, since the apron is the only way out, and nothing inside the garage has to move. You can park inside again the same day, once the hole patches have set.

Full answer on Garage Apron Repair →Link to this answer

How much does it cost to fix a sunken garage apron in Green Bay?

Usually $400 to $1,000 for a typical apron of about 100 square feet, lifted flush with the garage floor. Our job minimum is $300. Sealing the joint at the door adds its footage at $5 to $10 per foot, with no separate caulking minimum when it's done with the lift. An apron over a big washout can run higher; we'll say so from your photos.

Full answer on Garage Apron Repair →Link to this answer

Should I fix my garage apron before getting the garage floor coated?

Yes. Lift the apron first, so the coated floor ends at a flush, finished edge and water runs away from the door instead of onto the new coating. The joint at the door is sealed after the lift. We can price the lift and a garage floor coating from the same set of photos.

Full answer on Garage Apron Repair →Link to this answer

Is a lifted garage apron covered by a warranty?

Yes. Every lift comes with a written warranty, and the written warranty on your quote spells out what's covered before you approve it. Because the apron sits on backfill that soaks up roof water, keeping the joint at the door sealed and the nearby downspouts emptying away from the driveway does the most to keep it flush.

Full answer on Garage Apron Repair →Link to this answer

Sidewalk & Walkway Leveling →

Is a sunken sidewalk a trip hazard liability?

It can be. Uneven walks are one of the most common causes of trip-and-fall claims. For businesses, the ADA standards treat any change in level over 1/4 inch on an accessible route as something that needs to be addressed. Lifting the low section removes the hazard.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Who is responsible for fixing a public sidewalk in Green Bay?

Rules for sidewalks in the public right-of-way are set by each city, and responsibility can fall to the property owner. Check with your city's public works department; once it's approved, we can lift public sidewalk sections like any other.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

What if the city marked my sidewalk for repair?

Many cities inspect public sidewalks and notify the owner when a section has to be fixed, usually because a lip has passed their trip-hazard limit. If the section sank and is still in one piece, lifting it flush is often an accepted fix; your notice or the public works office will confirm what they require. We photograph and measure before and after, so you have a record to send back.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Can you grind a trip edge instead of lifting the slab?

Grinding works for small lips on slabs that heaved up slightly. When a section sank, grinding the high side leaves the low slab holding water. Lifting fixes the cause and keeps the walk draining.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Can one sunken sidewalk square be lifted by itself?

Yes. Each square is lifted on its own through 2 to 4 holes, each 5/8 inch, until it's flush with the squares on either side. You don't have to do the whole walk, though fixing every low joint in one visit costs less per square.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

How much does it cost to level a sidewalk in Green Bay?

Usually $300 to $600 for a single sunken square, and $300 to $1,250 for three to five squares of a front walk (about 50 to 125 square feet). Our job minimum is $300, so one square costs about the same as two; fix every low joint in one visit. Sealing the joints after the lift adds $5 to $10 per foot.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Is lifting a sidewalk square cheaper than letting the city replace it?

Not always, and we'll tell you which. The City of Green Bay lists historical costs of about $160 to $300 to replace a 5-by-5 panel, so on one or two squares the city's price can beat our $300 to $600. On a longer run of squares, or with your driveway or stoop on the same visit, lifting gets competitive and you keep your existing concrete.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

How flush will my sidewalk be after it's lifted?

Flush. Our target is no lip at all at each joint, not just under the 1/4-inch ADA limit. We lift each low square in short shots against a line, check every joint before we leave, and text you before-and-after photos with the measurements.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

How can I tell if a tree root pushed my sidewalk up or the square next to it sank?

Look down the walk: the square that's out of line with the rest is the one that moved. A root usually humps a square up near the tree; a sunken square sits below both neighbors and often holds water. Sunken squares lift. A heaved one can't be pushed down, so it's ground or replaced (we don't do either), or we lift the squares beside it to ease the lip.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Why does the same sidewalk square ice over every winter?

Usually because it sank and now holds a puddle that freezes night after night. Lifting it flush with its neighbors restores the pitch so water runs off, and sealing the joints keeps meltwater from getting under it and dropping it again. If a downspout empties across the walk, extending it helps too.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Will lifting close the gaps between my sidewalk squares?

No. Lifting fixes height, not width: it brings a low square up flush, but it doesn't slide squares back together. Open joints are filled after the lift with backer rod and flexible sealant, which keeps water, sand and weeds out so the soil under the walk stays put. That's our joint caulking service.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Can you lift the sidewalk where it meets my driveway?

Yes. Whichever side dropped gets lifted to meet the other: often it's the walk square, sometimes the driveway section beside it. Both can be done on the same visit and the same quote, and the joint between them is sealed afterward so water stops washing out the base there.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

My side walkway tilts toward the house. Can you fix that?

Usually, yes. A walk running along the house sits on the same foundation backfill as a patio, so its house-side edge settles and tips it toward the wall. We lift that edge until the walk falls away from the house again, then seal the joint along the foundation so roof water can't run down behind it.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Will there be a gap along the grass after my sidewalk is lifted?

Often a small one. Raising a square an inch or two leaves its edge standing a little above the soil beside it. Backfill that edge with topsoil and reseed it, so the base stays covered and water can't run in along the side of the walk.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Can lifting make my front walk safe for a walker or wheelchair?

It fixes the biggest problem: lips at the joints. We lift each low square flush with its neighbors, so wheels and walker feet roll across instead of catching, and the joint sealant is finished slightly below the surface. Lifting doesn't change how steep or narrow a walk is, so a walk with steps or a steep run still needs a ramp.

Full answer on Sidewalk & Walkway Leveling →Link to this answer

Patio Leveling →

Why is my patio sloping toward my house?

The soil along a foundation is backfill that settles for years after construction, and roof water keeps it wet. The patio edge resting on it sinks, which tips the whole slab toward the house.

Full answer on Patio Leveling →Link to this answer

Can water from a sunken patio cause basement leaks?

It can contribute. A patio pitched toward the house collects rain and snowmelt against the foundation, which raises the water pressure on the wall. Restoring the slope away from the house is one of the cheapest drainage fixes there is.

Full answer on Patio Leveling →Link to this answer

Can you lift a patio with a hot tub or pavers on it?

A hot tub needs to be drained and usually moved before lifting, because it adds too much weight and could crack the slab as it rises. Pavers are a different system; foam lifting is for poured concrete slabs.

Full answer on Patio Leveling →Link to this answer

What do I need to move before you lift my patio?

Furniture, planters, the grill and anything else on the low sections, plus a drained hot tub if there is one. Light items can stay on sections we aren't lifting. We need a clear path for a hose from the truck to the patio, and that's it; you don't need to be home.

Full answer on Patio Leveling →Link to this answer

How much should a patio slope away from the house?

At least 2%, which is about ¼ inch per foot, for paving next to a foundation. On a 12-foot-deep patio that's about 3 inches of fall from the house to the yard. That's the line we lift to, not dead level.

Full answer on Patio Leveling →Link to this answer

Can you lift the steps down to my patio at the same time?

Yes. Patio steps, whether from the door down to the patio or from the patio down to the yard, are usually poured separately from the patio, so they settle separately. We lift the patio first, then set the steps to meet it, all in one visit. The same goes for the walk that leaves the patio.

Full answer on Patio Leveling →Link to this answer

How can I tell if my patio slopes toward the house?

Lay a level or a straight board on the patio, pointing away from the house. If the bubble shows the slab falling toward the wall, or water stands along the house after rain, that side has sunk. A patio should fall at least 1/4 inch per foot away from the house. A photo taken along the house wall shows us the slope.

Full answer on Patio Leveling →Link to this answer

There's a downspout emptying onto my patio. Is that why it sank?

Often, yes. Roof water dumped at the patio edge soaks the backfill along the foundation and runs into the joints, washing soil out from under the slab. Lifting puts the patio back; extending the downspout past the patio keeps it there. Here's how to extend downspouts.

Full answer on Patio Leveling →Link to this answer

Can you lift a patio with a pergola or fire pit on it?

Often, yes. A pergola bolted to the slab rises with it, so we lift slowly from several holes and watch the posts. A built-in fire pit, seat wall or outdoor kitchen puts a lot of weight in one spot, so send a photo and we'll tell you whether that section can be lifted with it in place. A portable fire pit just gets moved.

Full answer on Patio Leveling →Link to this answer

Can you lift a patio that's under a deck or next to a window well?

Usually, yes. The foam goes in through 5/8-inch holes from a hose, so we only need room to drill and reach the slab. We keep the holes back from the foundation and clear of window wells, and inject in short shots while watching the joint at the wall. Low clearance under a deck can limit where we drill, so send a photo.

Full answer on Patio Leveling →Link to this answer

Can we use the patio the same day you lift it?

Yes. Most patios take a few hours, and you can walk on it and put the furniture and grill back as soon as we pack up. A drained hot tub can go back once the hole patches have set.

Full answer on Patio Leveling →Link to this answer

How much does it cost to level a patio in Green Bay?

Usually $600 to $1,500 for a patio of one or two slabs, about 150 square feet. Our job minimum is $300, and bigger patios run about $4 to $10 per square foot. A patio the hose reaches easily prices at the low end; one behind a fenced side yard or sitting over a big washout can run higher.

Full answer on Patio Leveling →Link to this answer

My stamped patio slopes toward the house. Is it fixed the same way?

Yes. We lift the house side until the patio falls away from the wall again, the same as a plain slab. On a stamped or colored patio the holes go in grout lines and darker texture, and the patches are tinted to blend, so the pattern stays intact. More on stamped and decorative leveling.

Full answer on Patio Leveling →Link to this answer

Should I replace my sunken concrete patio with pavers?

Not just to fix the slope. A paver patio means breaking out the concrete first, and the new one still sits on the same foundation backfill that let your slab sink. If your slab is in one piece or a few large pieces, lifting gets the slope back in a few hours. Pavers make sense when you want a new look, not a fix.

Full answer on Patio Leveling →Link to this answer

Is fall a good time to level a patio in Wisconsin?

Yes, it's one of the best. The furniture is usually put away, the ground isn't frozen yet, and fixing the slope before winter means spring snowmelt runs into the yard instead of against your basement wall. We lift from the spring thaw until the ground freezes, so book before the frost sets in.

Full answer on Patio Leveling →Link to this answer

Steps & Stoop Leveling →

Can you lift front steps that pulled away from the house?

Often, yes. If the stoop is solid concrete in one piece, foam can raise its outer edge and bring it back against the wall, and then the gap is sealed. We confirm it from photos first.

Full answer on Steps & Stoop Leveling →Link to this answer

Is my stoop sinking or is my house settling?

Almost always the stoop. Wisconsin's building code puts house footings at least 48 inches below grade, below the frost line, while a stoop sits on shallow backfill. If the gap at the wall is wider at the top or the top step tips outward, the stoop has moved, not the house.

Full answer on Steps & Stoop Leveling →Link to this answer

What if my steps are hollow?

Hollow stoops can sometimes be filled with foam and lifted, and sometimes the shell is too thin or cracked to lift safely. Send a photo of the side and any cracks and we'll tell you which it is.

Full answer on Steps & Stoop Leveling →Link to this answer

Can you lift the walk and landing in front of the steps in the same visit?

Yes, and it's usually needed. The walk square at the bottom step sits on the same backfill and often drops with the stoop, which is what makes the first step tall. We lift the stoop first, then bring the walk up to meet it so the bottom riser matches the others. The model residential code allows no more than 3/8 inch of difference between risers in a flight, and a tall bottom step is the one people trip on.

Full answer on Steps & Stoop Leveling →Link to this answer

The top step is lower than my front door threshold. Can lifting fix that?

Usually, yes. A top step that's dropped below the threshold is one of the clearest signs the stoop sank. We set our line to the threshold and lift until the top step sits just below it again, sloping slightly away from the house so rain runs off the front of the steps instead of toward the door.

Full answer on Steps & Stoop Leveling →Link to this answer

My stoop is tipping to one side. Can you level it?

Yes, if it's solid and in one piece. Stoops often sink more on one side, usually the corner where a downspout empties or water runs off the roof. We lift the low side until the landing and treads sit level side to side again, then seal the joint at the wall.

Full answer on Steps & Stoop Leveling →Link to this answer

Will lifting my stoop straighten the leaning railing?

Often. A railing post set in the stoop leans because the stoop tipped, so bringing the stoop back toward the wall brings the post back with it. If a bracket pulled out of the house wall or an anchor cracked the concrete, it may need re-fastening afterward, and we'll point that out. Include a photo of the railing base with your quote photos.

Full answer on Steps & Stoop Leveling →Link to this answer

Can foam really lift a heavy concrete stoop?

Yes. A solid 4 by 5 foot stoop two feet tall weighs about 5,800 pounds, but spread over its footprint it presses down at only about 2 psi. Cured lifting foam is rated at roughly 64 to 100 psi, so it lifts the stoop and holds it with a wide margin.

Full answer on Steps & Stoop Leveling →Link to this answer

When do front steps need to be replaced instead of lifted?

When the stoop is broken into pieces that move separately, when it's a hollow shell too thin or cracked to lift safely, or when the treads and edges are crumbling. A crack across an otherwise solid stoop doesn't rule out a lift. A photo of the side of the steps and any cracks usually tells us which you have.

Full answer on Steps & Stoop Leveling →Link to this answer

Can I still use my front door while you lift the stoop?

Plan on using another door for the 1 to 3 hours we're working, since we're drilling and injecting right at the landing. You can walk on the steps as soon as we pack up; the foam reaches about 90% of its strength in 15 minutes.

Full answer on Steps & Stoop Leveling →Link to this answer

How much does it cost to lift a stoop and seal the gap at the house?

Usually $300 to $600 to lift a small stoop; our job minimum is $300. Sealing the gap at the wall rides along at $5 to $10 per foot with no separate caulking minimum, so a typical 10 to 20 feet of stoop joint adds about $50 to $200. If the walk square at the bottom dropped too, it goes on the same quote.

Full answer on Steps & Stoop Leveling →Link to this answer

Can you lift back door and side door steps too?

Yes. Back stoops, the steps at a garage service door and the steps down from a patio door sit on the same foundation backfill as a front stoop and settle the same way, so they're lifted the same way. A small stoop prices near the job minimum, so it's worth doing them on the same trip as the front.

Full answer on Steps & Stoop Leveling →Link to this answer

Can I fill the gap at my stoop with spray foam from the hardware store?

No. Canned spray foam is a soft insulating foam, not a lifting foam: it won't raise the stoop, it breaks down in sunlight, and it isn't made to keep water out of an outdoor joint that moves. The gap needs flexible sealant over backer rod, and if the stoop already tipped, lift it first so you're not sealing in the bad slope.

Full answer on Steps & Stoop Leveling →Link to this answer

Should I fix a sinking stoop before winter?

If you can. Once a stoop pulls away, rain and snowmelt run into the gap at the wall, freeze and soften the soil underneath, so it tends to tip a little more every winter. We lift from the spring thaw until the ground freezes; after that, photos get you a price and a spot on the spring schedule.

Full answer on Steps & Stoop Leveling →Link to this answer

Is a lifted stoop covered by a warranty?

Yes. Every lift comes with a written warranty, and the written warranty on your quote spells out what's covered before you approve it. What keeps a stoop in place afterward is a sealed joint at the wall and a downspout that empties away from the steps, so check both each spring.

Full answer on Steps & Stoop Leveling →Link to this answer

Garage & Shop Floor Leveling →

Can you level a cracked or sunken garage floor?

If the floor slab is intact or cracked into a few large pieces and it sank and tree roots didn't push it up, yes. Foam lifts the low panels back in line with the rest of the floor, and cracks are repaired before any coating goes on.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Why is my garage floor sloping toward the door?

The outer edge of a garage floor sits closest to the apron and the driveway, where roof water and the foundation backfill are, so it's often the first part to settle. Foam lifts that edge back in line with the rest of the floor. If it's the apron outside the door that dropped instead, that's its own quick fix.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can you lift a garage floor and then coat it?

Yes, and that's the best order. We lift first, then grind, repair cracks and joints, and install the coating. The small injection holes are patched and covered by the coating.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Will the injection holes show through a floor coating?

No. The 5/8-inch holes are filled with cement grout, then ground flush with the rest of the floor during coating prep. The base coat and flake cover them completely.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Do I have to empty the garage before you lift the floor?

No. Cars out, and anything heavy off the panels we're lifting: a lift, a safe, a stack of tires. Shelving along the walls and the rest of your stuff can stay unless the low spot is under it. We work with the door open, the dust is vacuumed at the drill, and you're parking inside again the same day.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can you lift the garage floor and the driveway in the same visit?

Yes, and that's the right order. The floor is lifted first, then the apron and driveway are set to meet it, so the transition at the door ends up flush and pitched away from the garage. One trip means one job minimum, and the joint at the door is sealed at the end.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can you lift just one panel of the garage floor?

Yes. Each panel is lifted on its own through its own holes until it's back in line with its neighbors, so you don't pay to lift a floor that only dropped at one joint or corner. A single panel usually lands near the job minimum, so if the apron or a walk square is low too, send photos of those and we'll price the trip once.

Full answer on Garage & Shop Floor Leveling →Link to this answer

How much does it cost to level a sunken garage floor in Green Bay?

Usually $400–$1,000 for one sunken panel of about 100 square feet, and $800–$3,000 for two or three panels. Larger floors run about $4–$10 per square foot, with a $300 job minimum. A panel sitting over a big washout, often near a floor drain, can run higher, and we'll say so from your photos.

Full answer on Garage & Shop Floor Leveling →Link to this answer

How long does it take to lift a garage floor?

A few hours for most garage floors. We set the line, drill, lift each low panel and patch the holes with the door open, and you can walk on the floor as soon as we pack up and park inside again the same day once the grout in the holes has set.

Full answer on Garage & Shop Floor Leveling →Link to this answer

How do you fix an uneven joint in a garage floor?

Lift the low side. A step at a control joint means the panel on one side settled, and foam brings it back flush through 5/8-inch holes so a floor jack or snow shovel rolls across again. If both sides are solid and the lip is under about 1/4 inch, it can be ground flush during coating prep instead.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can you lift a garage floor panel that has a floor drain in it?

Usually, yes. Water getting in around the drain is often why the panel sank, so we keep the holes back from the drain, lift in short shots and set the line so the floor still falls toward it. If the drain line is leaking or broken, have a plumber fix it first, or the water will wash the base out again.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can you lift a garage floor that already has an epoxy or flake coating?

Yes, but the patches will show. We drill through the coating, lift the panel and fill the 5/8-inch holes with cement grout, which leaves small gray dots that can't match flake or a solid color. If the floor is due for a new garage floor coating anyway, lift first and the patches disappear under it.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can you level the floor in a detached garage or shop?

Yes. Detached garages and shops are often built on a thin or uncompacted base, so they drop at joints and corners, and we lift them the same way as an attached garage. Our rig carries its own power, so the building doesn't need electricity; we just need a hose path from the truck to the door.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Will a lifted garage floor hold a car lift, a gun safe or heavy tool chests?

Yes, once it's set. Cured lifting foam is rated at roughly 64–100 psi, and a typical 4-inch slab spreads the load across the panel; heavy items just come off the low area during the lift. For a car lift, the lift maker's slab requirements still apply, since foam supports the slab but doesn't make it thicker.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Can lifting fix a garage floor that was poured with the wrong slope?

Only if it sank. A step at a joint or crack, or a panel that sounds hollow, means a section settled, and lifting puts the pitch back toward the door. A floor that runs the wrong way evenly, with no steps, was usually poured that way, so there's nothing under it for foam to fix, and we'll tell you that from the photos.

Full answer on Garage & Shop Floor Leveling →Link to this answer

Stamped & Decorative Concrete →

Can stamped concrete be leveled without damaging the pattern?

Yes, in most cases. The slab is lifted as one piece, so the pattern itself isn't disturbed. The only marks are the 5/8-inch holes, which we place in grout lines and texture and patch with grout tinted to the surface.

Full answer on Stamped & Decorative Concrete →Link to this answer

Will the hole patches match my colored concrete?

Close, not perfect. We tint the patch grout to the surface and put the holes where the pattern hides them, but on weathered or sealed color a patch can read slightly different at first. Most people stop noticing them within a season.

Full answer on Stamped & Decorative Concrete →Link to this answer

Can you lift sealed or stained concrete?

Yes. Sealers and stains don't affect the lift; the drill goes through the sealer, and a sealed surface can be touched up over the patches afterward.

Full answer on Stamped & Decorative Concrete →Link to this answer

Why not just replace a sunken stamped patio?

Because a replaced section rarely matches. Stamp patterns, color and sealer change from pour to pour, so new decorative concrete next to old usually looks like a patch, and stamped concrete costs more to pour than plain. Lifting keeps the original surface.

Full answer on Stamped & Decorative Concrete →Link to this answer

How much does it cost to level stamped concrete in Green Bay?

About the same as plain concrete. A single stamped walk section usually runs $300–$600, a patio of one or two slabs (about 150 square feet) $600–$1,500, and larger areas about $4–$10 per square foot, with a $300 job minimum. Mapping the holes into the pattern and tinting the patches are part of the quote, not extras.

Full answer on Stamped & Decorative Concrete →Link to this answer

Can I see where the holes will go before you drill my stamped patio?

Yes. We map the pattern first and mark each hole in a grout line, a joint or the darkest part of the texture, and you can look over the marks before anything is drilled. The holes still need to be spread about 3 to 4 feet apart so the slab rises evenly, so a few may land where the pattern hides them less.

Full answer on Stamped & Decorative Concrete →Link to this answer

Can you lift exposed aggregate concrete?

Yes. It lifts like any other slab, and the stones on the surface aren't disturbed. The patches are what you'll notice: a grout plug can't copy the stones, so we put holes in joints where we can and tint the grout to blend, but up close you'll still see a few small, smooth dots.

Full answer on Stamped & Decorative Concrete →Link to this answer

How do you fix a crack running through a stamped pattern?

If one side dropped, we lift it flush first so the pattern lines up across the crack again. Then the crack is cleaned out and filled with flexible sealant set slightly low, so it reads as one more line in the pattern instead of a bead on top. It won't vanish, but water stops getting under the slab.

Full answer on Stamped & Decorative Concrete →Link to this answer

Should I reseal my stamped concrete after it's lifted?

It's a good time to. A fresh coat of decorative sealer over the tinted patches helps them blend with the rest of the surface. We can do both in one booking: we lift first, then reseal with a film-forming decorative sealer and an anti-skid additive once the patches have dried. The reseal is quoted from your photos.

Full answer on Stamped & Decorative Concrete →Link to this answer

How do I know if my stamped patio needs lifting or just resealing?

Look at the joints and pattern lines, not the color. A lip at a joint, a crack with one side lower, water standing where it used to drain off, or a section that rocks means it sank and needs lifting. Faded color, a white haze or peeling sealer is a sealer problem, and we can reseal it. A peeling or hazy film may need to come off first, and we'll tell you from the photos what that takes.

Full answer on Stamped & Decorative Concrete →Link to this answer

Can stamped concrete be mudjacked instead of foam lifted?

It can, but the holes are the problem. Mudjacking needs holes about 1½ to 2 inches across, which are hard to hide in a pattern, and pumps a slurry of about 100–150 lb per cubic foot under a finished surface. Foam goes in through 5/8-inch holes that fit in a grout line and weighs about 2–5 lb per cubic foot.

Full answer on Stamped & Decorative Concrete →Link to this answer

Can a stamped overlay fix a sunken patio?

No. An overlay follows the slab under it, so a section that sank or tips toward the house still does with a new pattern on top, and any movement can crack the overlay. Lift the slab back to the line first; if you still want a new surface, that comes after, from a decorative concrete contractor.

Full answer on Stamped & Decorative Concrete →Link to this answer

What if one section of my stamped concrete is too broken to lift?

That section gets replaced, and the rest can usually still be lifted. We don't pour or stamp concrete, so the new piece comes from a decorative concrete contractor, and lifting the other sections first lets them pour to slabs that are back where they belong. Expect the new section to look a little different, since stamp and color rarely match pour to pour.

Full answer on Stamped & Decorative Concrete →Link to this answer

Does leveling stamped concrete take longer than plain concrete?

A little. Mapping the holes into the pattern and tinting the patch grout add some time, but most stamped patios and walks are still done in a few hours, and you can walk on them as soon as we pack up.

Full answer on Stamped & Decorative Concrete →Link to this answer

What photos should I send for a stamped concrete leveling quote?

Three or four: a wide shot of the area, a tape measure at the worst drop, and a close-up of the pattern and texture so we can plan where the holes go. Send them and you'll get a firm price by text or email within 24 hours, usually without a site visit.

Full answer on Stamped & Decorative Concrete →Link to this answer

Porch Leveling →

Can you lift a porch that has roof posts sitting on it?

Often, yes. We lift slowly from several holes so the slab, the posts and the beam rise together, and we watch the post bases the whole time. If a post has already been shimmed or the beam has pulled off a post, we tell you from the photos whether lifting fixes it or a carpenter needs to be involved first.

Full answer on Porch Leveling →Link to this answer

How do I know if my porch is hollow underneath?

Look at the side. A solid porch has a concrete face down to the ground. A hollow one usually has a block or brick wall with a vent, a small door or a crawlspace access, and older homes often have a cold cellar under the porch. Send a photo of the side and we'll tell you.

Full answer on Porch Leveling →Link to this answer

Can you lift the porch and the steps at the same time?

Yes. Steps are usually poured separately from the porch, so they settle separately. We lift both in one visit, the porch first so the steps can be set to meet it.

Full answer on Porch Leveling →Link to this answer

Will lifting the porch close the gap at the house?

If the slab tipped away from the wall, lifting the outer edge rotates it back and closes most of the gap, and the slab ends up pitched slightly away from the door so rain stops running at the foundation. What's left of the gap is sealed with flexible sealant so water stops running in behind the porch.

Full answer on Porch Leveling →Link to this answer

Can you lift a porch that's attached to the house without hurting the foundation?

Yes. The foam goes under the porch slab and pushes up on the slab, not on the wall. The house sits on footings at least 48 inches down, well below anything the foam reaches, and we keep the holes back from the foundation edge. We inject in short shots and watch the joint at the wall, so the slab comes up to meet the house instead of pressing into it.

Full answer on Porch Leveling →Link to this answer

How much does it cost to level a concrete porch in Green Bay?

A small porch or landing usually runs $300–$600, and our job minimum is $300. A larger porch of one or two slabs (about 150 square feet) usually runs $600–$1,500, and steps lifted in the same visit go on the same quote. Photos of the side, the gap at the wall and any post bases get you a firm price by text or email within 24 hours.

Full answer on Porch Leveling →Link to this answer

How long does it take to lift a porch?

Usually 1 to 3 hours on site. A porch carrying roof posts takes toward the longer end, since we lift in smaller shots and watch the post bases, and you can walk on the porch as soon as we pack up.

Full answer on Porch Leveling →Link to this answer

Is my porch roof sagging because the slab sank?

It can be. If the roof posts sit on the porch slab and the slab dropped, the posts and beam dropped with it, and lifting the slab brings them back up together. If the posts stand on their own footings or the slab is still level, the sag is in the framing, which is a carpenter's job, and a photo of each post base tells us which.

Full answer on Porch Leveling →Link to this answer

Can you lift a porch slab around brick or stone columns?

Usually. If a column stands on its own footing, it didn't sink, so we lift the slab up to meet it and seal the joint around its base. If the column sits on the slab and dropped with it, we lift slowly from holes around it so the column and the roof above rise evenly; send a close photo of where each column meets the slab.

Full answer on Porch Leveling →Link to this answer

Is it better to lift a covered porch or replace it?

If the slab is solid, lift it. Replacing a porch slab under a roof means shoring the posts, breaking out concrete against the house and pouring in a tight spot, and the new slab goes back on the same fill. Lifting usually takes an afternoon and never touches the roof, though a porch that's hollow underneath or broken into many pieces is the exception.

Full answer on Porch Leveling →Link to this answer

Can you lift a wraparound porch?

Yes. A wraparound porch is usually poured in several sections, and each one settles on its own, often most where a downspout empties beside it. We lift the low sections one at a time to a single line along the house, so the joints meet flush, then seal those joints along with the joint at the wall.

Full answer on Porch Leveling →Link to this answer

Can you lift a porch that has a cold cellar under it?

Not with foam. A porch over a cold cellar or crawlspace is a slab carried by the walls around it, and the space underneath is supposed to be there, so filling it isn't the fix. If that kind of porch is sagging or cracked, it needs a look at how the slab is supported, and we'll tell you that from the photos rather than quote a lift.

Full answer on Porch Leveling →Link to this answer

How do I get my porch ready for lifting?

Clear furniture, planters and anything heavy off the porch, and make sure we can run a hose from the driveway to it. Roof posts and railings stay where they are, but tell us if a railing is also fastened to the house wall, because the porch end will move and the house end won't. You don't need to be home.

Full answer on Porch Leveling →Link to this answer

Can you level a wooden porch?

No. Foam lifting is for poured concrete slabs on the ground, so a wood porch on posts, piers or a crawlspace is a job for a carpenter or deck builder. If the porch floor is a concrete slab and only the posts, steps or railings are wood, the slab can usually be lifted, and photos tell us which you have.

Full answer on Porch Leveling →Link to this answer

Why does water or ice collect on my porch landing?

Usually because the landing settled and tipped back toward the door, or dropped in one spot, so rain and roof drip sit there and freeze. Lifting it back to a slight fall away from the door lets water run off before it turns to ice. Check the gutter above it too, since roof runoff landing on the porch is often what softened the soil underneath.

Full answer on Porch Leveling →Link to this answer

Pool Deck Leveling →

Can you lift a pool deck without damaging the pool?

Yes, with care. We keep the holes back from the coping, skimmer, lights and plumbing, lift from the outside edge in small shots and watch the slab the whole time, so the foam fills the void under the deck instead of pushing on the pool wall. Tell us where your plumbing runs if you know; if you don't, we work from the equipment pad and skimmer locations.

Full answer on Pool Deck Leveling →Link to this answer

Can you lift the concrete deck around an above-ground pool?

Yes, if it's a poured slab. We keep the holes away from the pool wall and its footing ring and lift the slab back to a gentle fall away from the pool. Pavers or a wood deck around the pool are a different job.

Full answer on Pool Deck Leveling →Link to this answer

Should I lift my pool deck before or after the pool is closed for the season?

Either works. Fall is a good time: the pool is covered, the deck is clear, and the lift stops another winter of water running into the gap. We lift from the spring thaw until the ground freezes, so late fall is fine as long as the soil isn't frozen.

Full answer on Pool Deck Leveling →Link to this answer

What about the joint between the deck and the coping?

That flexible expansion joint stretches or tears as the deck sinks. After the lift we re-seal it along with the other joints. Keeping it sealed keeps splash water out of the backfill, which is what let the deck drop in the first place.

Full answer on Pool Deck Leveling →Link to this answer

Does the pool need to be drained before you lift the deck?

No. The pool stays full, open or covered, and a full pool is actually better: the water supports the shell and the liner, and nothing we do touches the water. The foam is closed-cell and doesn't absorb water, so the damp backfill around a pool doesn't affect it either.

Full answer on Pool Deck Leveling →Link to this answer

What do I need to move off the pool deck before you lift it?

Furniture, planters, the grill and anything else sitting on the low sections. The pool fence, ladder, slide and equipment stay unless they sit right where a hole needs to go or block the hose from the truck, and we'll tell you from the photos. The pool itself stays open or covered, whichever it is.

Full answer on Pool Deck Leveling →Link to this answer

Can you lift the pool coping or the pool steps?

It depends on what they're attached to. Coping that was poured as part of the deck rises with it. Coping stones set on the pool wall belong to the pool, not the deck, so they stay put and we lift the deck flush to them. Steps inside the pool are part of the shell and aren't lifted; concrete steps leading up to a raised deck are a slab and can be.

Full answer on Pool Deck Leveling →Link to this answer

How much does it cost to level a pool deck in Green Bay?

A single small section usually runs $300–$600. Most decks have two to six low sections, and 200–300 square feet usually lands at $800–$3,000, with bigger areas about $4–$10 per square foot. Sections over a big washout from splash water can run higher, and we'll say so from your photos.

Full answer on Pool Deck Leveling →Link to this answer

How soon can we swim after you lift the pool deck?

The same day. Most decks take a few hours, you can walk on the deck as soon as we pack up, and the pool stays open or covered the whole time because nothing we do touches the water.

Full answer on Pool Deck Leveling →Link to this answer

Can you lift the deck around a vinyl liner or fiberglass pool?

Yes. Liner and fiberglass pool walls are more flexible than a concrete shell, so we treat the wall as the one thing not to push on. The holes stay well back from the coping, the deck comes up in short shots from the outer edge, and the pool stays full so the water supports the wall and liner.

Full answer on Pool Deck Leveling →Link to this answer

Can the lifting foam get into the pool water or change its chemistry?

No. The foam goes under the deck slab, outside the pool shell, and cures within minutes into an inert, closed-cell plastic that doesn't dissolve or leach. Nothing we inject goes in the water, and we clean up the deck before we leave.

Full answer on Pool Deck Leveling →Link to this answer

Why does rain run back into my pool from the deck?

Because a deck section has settled and lost the gentle fall away from the pool it was poured with. Rain and dirt then run back over the coping, or water sits on the deck. Lifting the low sections restores the fall toward the yard, and sealing the joints keeps splash water out of the fill that let them drop.

Full answer on Pool Deck Leveling →Link to this answer

Why did my pool deck drop after the winter?

Usually water in the backfill. Splash-out and fall rain soak into open joints and the loose fill around the pool, then freeze, swell and thaw softer, so the deck can sit lower each spring. Lifting puts it back, and sealing the joints and the coping line before winter keeps that water out of the fill.

Full answer on Pool Deck Leveling →Link to this answer

Where should pool backwash and drain-down water go to protect the deck?

Away from the deck: well past the edge of the concrete, to wherever your local rules allow pool water to go. Backwashing and lowering the pool for winter dump a lot of water at once, and when it runs along the deck edge or into joints it carries fine soil out from under the slabs.

Full answer on Pool Deck Leveling →Link to this answer

Can you lift my pool deck and then coat it?

Yes, and that's the order it has to go. A coating can't level a deck that dropped away from the coping, so we lift the low sections first, then the deck is prepped and gets a UV-stable polyaspartic coating with grit in the topcoat. The hole patches end up under the coating.

Full answer on Pool Deck Leveling →Link to this answer

AC Pads, Sheds & Other Slabs →

Can you level a tilting air conditioner pad?

Yes, and the unit stays connected. We drill one to three 5/8-inch holes in the pad beside the condenser, raise the pad in small steps while watching the line set, and patch the holes. It usually takes under an hour. If the lines are already kinked from the tilt, have your HVAC company check them before we lift.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Can you lift a basement floor?

Yes. Floor coverings come up over the low area, we drill through the slab, inject foam and patch the holes flush, with dust vacuumed at the drill. If water comes up through the floor, fix the drainage first; lifting doesn't stop water and foam under a slab doesn't waterproof it.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Is a small slab worth lifting, or is it cheaper to pour a new pad?

Lifting is usually cheaper once you count what sits on the slab. A new AC pad means the HVAC company disconnects, recovers refrigerant and reconnects the unit, which costs more than the pad; lifting keeps it connected. A new shed floor means emptying the shed. Lifting is an hour or two and the slab is back in use the same day.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Can you lift a sunroom or three-season room floor?

If the floor is a concrete slab on the ground, usually yes; we lift it from inside or from the exposed edge. Tell us if the slab has in-floor heat or snow-melt lines, because we won't drill a heated slab blind. A sunroom on a block or wood foundation is a different problem, and we'll tell you from the photos.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

What does it cost to lift a small concrete pad or shed floor in Green Bay?

A single small pad, like an AC, generator or mailbox pad, usually runs $300–$600, and our job minimum is $300. Larger slabs, such as a shed floor or part of a basement floor, run about $4–$10 per square foot. Several low spots in one visit are priced as one trip, so send photos of all of them.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

What if my AC lines were replaced after the pad started sinking?

Have your HVAC company check them before we lift. Lines that were cut or rerouted to fit the sunken position can be pulled tight when the pad comes back up. Send us photos anyway, and we can time the lift with your HVAC visit so the line work and the lift happen together.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Can you lift a plastic or composite AC pad?

No, and you don't need us for it. Foam lifting is for concrete pads. Lightweight plastic or composite pads, common on newer installs, are usually re-leveled by your HVAC company with compacted gravel underneath, often at a regular tune-up.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Why does my heat pump pad keep sinking?

Mostly water at the edge. A heat pump sheds meltwater every time it defrosts in winter, and with roof drip and downspouts that keeps the loose backfill beside the foundation wet. Foam fills the voids and lifts the pad without adding weight, and extending downspouts and grading soil away from the pad helps keep it there.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Can I just jack up my AC pad and pack gravel under it?

We wouldn't. The pad and unit together can weigh several hundred pounds, it's easy to yank on the refrigerant lines while prying, and hand-packed gravel rarely supports a pad evenly, so it tends to settle again. Foam fills the void under the whole pad and raises it in small steps with the unit still connected.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Can you lift a shed floor with the shed still on it?

Yes. The shed stays put, and the walls sitting on the slab come up with it. Move the mower and anything heavy off the low area, and we lift the corners and joints that dropped, usually in an hour or two; thin floors poured on uncompacted gravel are the usual case, and they lift fine if they're still in one or a few large pieces.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Will lifting my shed floor fix a door that won't close?

Often, yes. When a corner or edge of the slab drops, the wall on it drops too and racks the door frame, so the door sticks or won't close square. Lifting that part of the slab back usually lets it close again, though a frame that has warped or rotted may still need adjusting.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Should I lift my basement floor before installing flooring or a coating?

Yes, if a section dropped. Flooring and coatings follow the slab, so a step at a crack or a low edge along a wall shows right through them. Lift the low section first, then patch and lay flooring or a basement floor coating; shallow dips on a floor that hasn't moved are a job for the flooring installer, not foam.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

When can I put my hot tub back on the pad after it's lifted?

Usually the same day, once the grout in the holes has set, and we'll tell you when before we leave. The tub has to be drained and moved for the lift, but once it's back, cured foam rated at roughly 64–100 psi carries far more than a filled hot tub puts on the pad.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Does my standby generator have to be moved to level its pad?

No. The generator stays on the pad and stays connected, and we raise the pad in small steps while watching the gas line and wiring, the same way we watch an AC line set. If the gas line looks tight or was rerouted after the pad sank, have your generator installer check it before we lift.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Do small jobs like an AC pad come with a warranty?

Yes. Every lift comes with a written warranty, a single AC pad or shed floor included, and the written warranty on your quote spells out what's covered before you approve the job. Keeping downspouts and condensate draining away from the pad is the best thing you can do to keep it level.

Full answer on AC Pads, Sheds & Other Slabs →Link to this answer

Floor coatings

Polyurea flake floors for garages, basements, shops, patios and commercial space: prep, cure time, finishes and what makes a coating last.

Garage floor coatings →

Floor Coating FAQ: all 90 coating questions on one page →
Cost & pricing · Materials & chemistry · Prep & install · Warranty & longevity · Care & durability · Booking & scheduling · Basement floors · Shops & pole barns · Commercial floors · Patios, porches & pool decks · Full flake · Partial flake · Solid color
Show Hide 69 questions from 10 pages

Garage Floor Coatings →

How long until I can walk and park on a coated garage floor?

For our polyurea and polyaspartic system, foot traffic is usually fine within a few hours and parking after about 24 to 48 hours, depending on temperature. Epoxy-only systems can need up to a week. We give you exact times for your floor before we start.

Full answer on Garage Floor Coatings →Link to this answer

Do you install epoxy garage floors?

No. We install polyurea flake floors with a polyaspartic topcoat, which give you what most people are picturing when they ask for epoxy: a hard, glossy, flaked garage floor. Our system cures faster, doesn't yellow in sunlight and handles hot tires and cold weather better than an epoxy-only floor, so you can usually park on it in 24 to 48 hours instead of a week.

Full answer on Garage Floor Coatings →Link to this answer

Is a flake garage floor slippery when wet or snowy?

Less than you'd think. The flake and topcoat create a textured surface, and the topcoat texture can be adjusted. Any smooth floor gets slicker with ice or oil on it, so we set the texture for a Wisconsin garage.

Full answer on Garage Floor Coatings →Link to this answer

Will road salt and hot tires damage a coated floor?

A properly bonded professional coating resists road salt, brine and hot-tire pickup. Hot-tire peeling is mostly a problem with thin, roll-on epoxy over a poorly prepared floor.

Full answer on Garage Floor Coatings →Link to this answer

Can you coat a floor that has cracks or an old coating?

Yes. Cracks are filled and repaired as part of prep. An old coating that's peeling has to be ground off first, because a new coating is only as strong as the one under it.

Full answer on Garage Floor Coatings →Link to this answer

How long does a garage floor coating last?

Cost guides cite 10 to 20 years or more for a professionally installed polyaspartic floor in a home garage, far longer than a DIY kit. Prep, film thickness, traffic and care decide where in that range a floor lands.

Full answer on Garage Floor Coatings →Link to this answer

Can garage floors be coated in cold weather?

Coatings have minimum temperatures for the air and the slab. An attached garage can often be coated into late fall, sometimes with heat; a cold detached garage may need to wait for spring. We check temperatures before scheduling.

Full answer on Garage Floor Coatings →Link to this answer

What flake colors do you offer?

Dozens of blends, from light grays to dark mixes with accents. Lighter blends hide dust, darker ones hide tire marks. We bring physical samples so you see the real color.

Full answer on Garage Floor Coatings →Link to this answer

What is CSP, and why does it matter for a garage coating?

CSP, or concrete surface profile, is the International Concrete Repair Institute's scale for how rough prepared concrete is, from CSP 1 (nearly smooth) to CSP 10 (very rough). Broadcast garage coatings bond best at about CSP 2 to 3, which a diamond grinder produces; a smooth or etched floor gives the coating little to grip.

Full answer on Garage Floor Coatings →Link to this answer

How much does it cost to coat a one-car or three-car garage?

With us, about $2,000–$2,592 for a one-car garage of about 288 square feet and $5,184–$7,776 for a three-car garage of about 864 square feet, at $6–$9 per square foot with a $2,000 minimum. Nationally it's roughly $4 to $12 per square foot installed (HomeGuide). Send a photo of your floor and its size for a firm price by text or email within 24 hours. The cost guide covers two-car sizes.

Full answer on Garage Floor Coatings →Link to this answer

How much more does polyaspartic cost than epoxy, and is it worth it?

Nationally, installed polyaspartic runs about $5 to $12 per square foot and epoxy about $4 to $10 (HomeGuide), so the gap is usually small. For a Wisconsin garage we think it's worth it: you park in 24 to 48 hours instead of up to a week, the topcoat won't yellow, and it resists hot tires better. Prep still matters as much as the chemistry. Ours is $6–$9 per square foot installed.

Full answer on Garage Floor Coatings →Link to this answer

How long does it take to install a garage floor coating?

Usually one day for a one- or two-car garage. Grinding, crack repair, base coat, flake and topcoat all happen in the same visit; a big floor or one with an old coating to grind off can take longer. You can walk on it within a few hours and park after about 24 to 48 hours.

Full answer on Garage Floor Coatings →Link to this answer

What do I need to do to get my garage ready for the coating?

Empty the floor completely: cars, shelving, freezers, bikes and anything else sitting on it. Things hung on the walls can usually stay. Light items can come back once the floor is walkable, a few hours after we finish, but heavy shelving, tool chests and anything on wheels should wait until it's ready for cars, about 24 to 48 hours.

Full answer on Garage Floor Coatings →Link to this answer

Do I still need garage floor mats with a coated floor?

Not to protect the concrete. On a coated floor, salty slush sits on top instead of soaking in, and a squeegee pushes it out the door. Some people keep a containment mat anyway to hold meltwater in one spot through a long Wisconsin winter, which is fine; just lift it and clean under it now and then.

Full answer on Garage Floor Coatings →Link to this answer

Is a garage floor coating worth it if I'm selling my house?

It can help the house show better, but don't count on getting every dollar back in the sale price. A clean, bright garage floor photographs well and tells buyers the place was cared for. If you're listing in a few months it's mostly presentation; if you'll stay a few more years, you get to enjoy it too.

Full answer on Garage Floor Coatings →Link to this answer

Epoxy vs. Polyaspartic →

Which is better for a Wisconsin garage, epoxy or polyaspartic?

For a garage that sees road salt, hot tires and cold winters, a system with a polyaspartic topcoat is usually the better choice because it resists UV, cures in cooler temperatures and holds up to hot tires. The base coat and prep matter as much as the topcoat.

Full answer on Epoxy vs. Polyaspartic →Link to this answer

Is polyurea the same as polyaspartic?

Polyaspartic is a type of aliphatic polyurea. In the coatings trade the terms often overlap; both describe fast-curing, UV-stable coatings commonly used for garage floors.

Full answer on Epoxy vs. Polyaspartic →Link to this answer

Does epoxy turn yellow?

Most epoxies amber or yellow with sun exposure. That's why epoxy is often used as a base coat and covered with a UV-stable topcoat.

Full answer on Epoxy vs. Polyaspartic →Link to this answer

Does epoxy or polyaspartic cure faster?

Polyaspartic, by a wide margin. It can be recoated within hours, so most one- and two-car garages are finished in a day, walkable in a few hours and ready for cars in about 24 to 48 hours. Epoxy often needs a day or more per coat and up to about a week before you park on it.

Full answer on Epoxy vs. Polyaspartic →Link to this answer

When does an epoxy floor still make sense?

As a base coat under a UV-stable topcoat, where its bond and build are an asset, and in rooms with no sunlight on the floor and no rush to put a car back, where yellowing and a slow cure matter least. It also tends to cost slightly less. We don't install it ourselves; our floors are polyurea and polyaspartic.

Full answer on Epoxy vs. Polyaspartic →Link to this answer

Will a polyaspartic floor peel the way my epoxy kit did?

Not if it's bonded into ground concrete. Kits peel because a thin film sits on acid-etched concrete, and hot tires lift it. A professional floor is diamond ground first and built in layers to a real thickness. Poor prep will fail under any chemistry, so ask how the floor is prepared; why coatings peel covers the causes.

Full answer on Epoxy vs. Polyaspartic →Link to this answer

Why Coatings Peel →

Why did my garage floor epoxy peel?

Usually because it never bonded well: the floor was etched instead of ground, oil or a sealer was in the way, moisture pushed up through the slab, or a thin coat softened under hot tires and lifted with them.

Full answer on Why Coatings Peel →Link to this answer

Diamond grinding vs. acid etching: what's the difference?

Acid etching chemically roughens the surface a little and can leave residue. Diamond grinding mechanically removes the weak top layer and leaves a consistent profile, which gives a coating a much stronger bond.

Full answer on Why Coatings Peel →Link to this answer

Can you coat over an old peeling coating?

No. A new coating can only be as strong as what's under it. The old coating is ground off first, then the floor is prepped and coated.

Full answer on Why Coatings Peel →Link to this answer

Why is my garage floor coating peeling where the tires sit?

That's hot-tire pickup. A thin coating softens under tires coming off a hot road, sticks to the rubber and lifts when you back out. It's mostly a problem with thin roll-on epoxy over etched concrete. A floor bonded into ground concrete and built in layers to a real thickness resists it.

Full answer on Why Coatings Peel →Link to this answer

Does moisture make a garage floor coating bubble or peel?

Yes. Water vapor moving up through the slab pushes on a coating from below until it blisters or lets go. White powder on the floor or an old coating that's bubbling are signs to test before recoating. A slab with moisture coming through may need a moisture-tolerant base coat, and an active leak has to be fixed first.

Full answer on Why Coatings Peel →Link to this answer

Can a peeling spot be patched, or does the whole floor get redone?

A chip in a well-bonded floor can be repaired on its own. Peeling is different: it means the bond failed, so a patch would sit on a layer that's still letting go. A peeling floor is ground off and redone, and that removal is priced on your quote before you decide.

Full answer on Why Coatings Peel →Link to this answer

Basement Floor Coatings →

Can you coat a basement floor that gets damp?

Often, yes. We test the slab first. Damp from vapor moving through the concrete can usually be handled with a moisture-tolerant base coat. An active leak, standing water or a floor that floods needs the water fixed first, because no coating holds back water under pressure.

Full answer on Basement Floor Coatings →Link to this answer

How do you test a basement floor for moisture before coating it?

With a calcium chloride test (ASTM F1869) or an in-slab humidity probe (ASTM F2170), which give a real number instead of a guess. That number decides whether the floor gets our standard base coat, a moisture-tolerant one, or needs a water problem fixed first. Taping a square of plastic to the floor gives you a hint at home, not a number.

Full answer on Basement Floor Coatings →Link to this answer

Will a coating stop my basement floor from sweating?

It can't change the humidity in the room, so condensation can still form on a cold floor in summer. A dehumidifier handles that. What a coating does is keep spills, stains and dust out of the concrete and make the floor easy to wipe up.

Full answer on Basement Floor Coatings →Link to this answer

Why does paint keep peeling off my basement floor?

Usually moisture. Water vapor moving up through the slab pushes on a thin film of paint sitting on smooth, unground concrete until it bubbles and lets go. We grind the old paint off, test the slab, and bond the coating into the ground concrete with a base coat matched to what the test shows.

Full answer on Basement Floor Coatings →Link to this answer

Can you coat around a sump pit and floor drain?

Yes. The coating runs right up to the sump basin and floor drains, the lid and grates still lift out, and water still flows where it should. If the slab has dropped around the pit or drain, it gets lifted first, because a coating follows the floor and can't level it.

Full answer on Basement Floor Coatings →Link to this answer

How much does it cost to coat a basement floor in Green Bay?

Ours is $6–$9 per square foot installed, with a $2,000 minimum, so an 800-square-foot basement runs $4,800–$7,200. Where yours lands depends on what the moisture test shows, crack repair and any old paint to grind off; a moisture-tolerant base coat is priced on top. Nationally, professional floor coatings run about $4 to $12 per square foot installed (HomeGuide). We price from photos of the floor, by text within 24 hours, and confirm the base coat with a moisture test before we start.

Full answer on Basement Floor Coatings →Link to this answer

Shop & Pole Barn Floors →

Can you coat a pole barn floor that isn't heated?

Yes, when the slab and the air are within the coating's temperature range for the install and the cure. Polyaspartic cures in cooler conditions than epoxy, but in an unheated building we schedule for late spring through early fall, and we check the slab temperature before we start.

Full answer on Shop & Pole Barn Floors →Link to this answer

Will a floor coating hold up to a tractor or skid steer?

Rubber tires, yes. Steel tracks, chains and buckets dragged across the floor can gouge any coating. Tell us what drives on the floor and we'll plan the finish around it.

Full answer on Shop & Pole Barn Floors →Link to this answer

Should I coat my shop floor before or after installing a car lift?

Before, if you can: the floor gets coated in one piece and the lift is anchored through the finished coating. If the lift is already in, we coat around the posts.

Full answer on Shop & Pole Barn Floors →Link to this answer

Can you coat a shop floor that's soaked with years of oil?

Usually, yes. Oil-soaked areas get degreased, then ground out or treated with a primer made for it, because oil left in the concrete is one of the main reasons coatings peel. Deep, decades-old stains take the most work, so show us the worst spots in your photos.

Full answer on Shop & Pole Barn Floors →Link to this answer

How long does it take to coat a large shop or pole barn floor?

It depends on the square footage and how much repair and degreasing the slab needs. A shop about the size of a two-car garage is usually a one-day job; a big pole barn floor takes longer, and you'll get the schedule with your quote. Vehicles and equipment on rubber tires can go back on after about 24 to 48 hours.

Full answer on Shop & Pole Barn Floors →Link to this answer

How much does it cost to coat a shop or pole barn floor?

Ours is $6–$9 per square foot installed, with a $2,000 minimum, so a 30-by-40 shop of 1,200 square feet runs $7,200–$10,800. Repairs, oil-soaked areas and the finish set where yours lands. Nationally, professional floor coatings run about $4 to $12 per square foot installed (HomeGuide). Our firm price comes from photos of the floor and its size, by text within 24 hours.

Full answer on Shop & Pole Barn Floors →Link to this answer

Commercial Floor Coatings →

How long is a commercial space out of use for a floor coating?

Most smaller spaces are coated in a day. People can walk on a polyaspartic floor within a few hours, and vehicles can go back on it after about 24 to 48 hours. We plan the install around your closed days or a weekend.

Full answer on Commercial Floor Coatings →Link to this answer

Can you coat our floor on a day we're closed?

Yes, that's how most commercial jobs are planned. Most smaller spaces are coated in a day, and people can walk on a polyaspartic floor within a few hours, so after a Sunday or holiday install you can usually open on schedule the next morning. Areas where vehicles park need about 24 to 48 hours.

Full answer on Commercial Floor Coatings →Link to this answer

Can you coat our floor in sections so we can stay open?

Often, yes. On a larger floor we can split the work at doorways or other clean lines and close one area at a time while the rest stays in use. Each area has to be cleared of shelving and fixtures first, and the coating smell carries, so we plan ventilation for the side that's open.

Full answer on Commercial Floor Coatings →Link to this answer

Does a coated commercial floor meet ADA slip-resistance requirements?

It can, with grip built in. The ADA standards require floors on accessible routes to be stable, firm and slip resistant without setting a test number, so we add flake texture and grit in the topcoat at entries, restrooms and anywhere the floor gets wet. Walk-off mats at the door still help in winter.

Full answer on Commercial Floor Coatings →Link to this answer

Is a polyaspartic coating right for forklifts or a commercial kitchen?

Not always. It suits foot traffic, carts and vehicles on rubber tires, but constant forklift traffic, food processing and harsh chemicals call for specialty industrial systems, which we don't install. Send photos and tell us how the floor is used, and we'll tell you honestly whether yours is a fit.

Full answer on Commercial Floor Coatings →Link to this answer

How much does a commercial floor coating cost in Green Bay?

Our polyurea flake floors start at $6–$9 per square foot installed with a $2,000 minimum; nationally, professional floor coatings run about $4 to $12 (HomeGuide). Where your floor lands depends on the square footage, crack and joint repair, any old coating to remove and the finish. Send photos and rough dimensions of each area for a price by text or email within 24 hours.

Full answer on Commercial Floor Coatings →Link to this answer

Patio, Porch & Pool Deck Coatings →

Can you put a garage-style flake coating on a concrete patio?

Yes, with a UV-stable polyaspartic and grit in the topcoat so it isn't slick. The patio has to be sound, level and draining away from the house first; a sunken or tipped patio gets lifted before it's coated.

Full answer on Patio, Porch & Pool Deck Coatings →Link to this answer

Should I coat or seal my patio?

Seal it if you like how it looks and want it protected from water and salt. Coat it if you want it to look new, with stains and patches covered. Covered porches and pool decks are the usual coating jobs.

Full answer on Patio, Porch & Pool Deck Coatings →Link to this answer

Is a coated pool deck slippery?

Not with grit in the topcoat, which is how we finish pool decks. Any wet surface around a pool deserves care, but a gritted coating grips far better than a smooth one.

Full answer on Patio, Porch & Pool Deck Coatings →Link to this answer

Will a porch coating peel like porch paint does?

Not when the slab is prepped right. Porch paint is a thin film over concrete that's usually only washed, so water and freeze-thaw lift it. We grind the paint and weak surface down to sound concrete and bond a much thicker polyaspartic into it. A slab that stays wet or crumbles underneath can still cause trouble, so we check it first.

Full answer on Patio, Porch & Pool Deck Coatings →Link to this answer

If you can coat a patio, why not my driveway?

Because a driveway gets plowed, shoveled, salted and driven on in every kind of weather. A penetrating sealer protects it from water and salt without adding a layer on top for all that to wear on. That's why we recommend sealing driveways and walks, and coating the porches, patios and pool decks you want to look new.

Full answer on Patio, Porch & Pool Deck Coatings →Link to this answer

How much does it cost to coat a patio or porch in Green Bay?

Outdoor coatings are $7–$10 per square foot installed, with a $2,000 minimum, so a 16 × 20 patio (320 square feet) runs $2,240–$3,200 and a small porch comes in at the minimum. The size, crack and surface repair, any lifting needed first and the finish you pick are what move the price. Nationally, professional floor coatings run about $4 to $12 per square foot installed (HomeGuide). We price yours from photos and send a firm number by text within 24 hours.

Full answer on Patio, Porch & Pool Deck Coatings →Link to this answer

Full Flake Floors →

What does full broadcast mean on a flake floor?

Flake is thrown into the wet base coat until it won't hold any more, so the whole floor is covered and no base color shows. The loose flake is scraped off and a clear topcoat seals it in.

Full answer on Full Flake Floors →Link to this answer

Is full flake better than partial flake?

For a garage, usually. Full flake hides dust, salt and tire marks best and has the most texture. Partial flake shows more of the base color for a cleaner look, which suits basements and showrooms.

Full answer on Full Flake Floors →Link to this answer

What flake sizes are there for a full flake floor?

Flake comes in several chip sizes. Bigger flakes make a bolder, busier pattern; smaller ones look finer and more like stone. Size changes the look, not how long the floor lasts, so pick the one you like on the real samples we bring.

Full answer on Full Flake Floors →Link to this answer

Which full flake color blend hides road salt and dirt best?

A light or mid-tone blend. Road salt dries to a white film, and lighter blends hide it along with dust and make the garage brighter. Dark blends hide tire marks and oil drips but let that salt film show. A blend that mixes light, mid and dark chips covers the most.

Full answer on Full Flake Floors →Link to this answer

How thick is a full flake floor?

Thicker than a partial flake floor or a roll-on kit. Each polyaspartic coat goes on at about 6 to 12 mils dry, and a full flake system stacks a base coat, a solid layer of flake and a clear topcoat. That thickness, plus a bond into ground concrete, is what keeps hot tires from lifting it.

Full answer on Full Flake Floors →Link to this answer

How much does a full flake floor cost in Green Bay?

Ours is $6–$9 per square foot installed, with a $2,000 minimum; a 24 × 24 two-car garage runs $3,456–$5,184. Nationally, professional coatings run about $4 to $12 (HomeGuide). Your firm price comes from photos of the floor and its size, by text within 24 hours. Size, crack and pit repair, any old coating to grind off and the flake size you pick all move the number. See the coating cost guide.

Full answer on Full Flake Floors →Link to this answer

Partial Flake Floors →

What is a partial flake floor coating?

A colored base coat with a lighter scatter of flake, sealed under a clear topcoat. The base color shows between the flakes, for a cleaner look than a full flake floor.

Full answer on Partial Flake Floors →Link to this answer

How much flake goes on a partial flake floor?

Your choice, from a light speckle to a heavy scatter. More flake hides more dust and adds texture; less lets the base color carry the look. The flake is scattered by hand, so we can match the density to the sample you pick.

Full answer on Partial Flake Floors →Link to this answer

Is a partial flake floor slippery?

It's smoother than a full flake floor, so where it gets wet, like an entry or a laundry area, we add grit to the topcoat for grip.

Full answer on Partial Flake Floors →Link to this answer

When is partial flake the wrong choice?

In a garage that takes slush and road salt all winter. There, full flake hides more and grips better, which is why it's our standard for garages. Partial flake works best in rooms that stay fairly clean, like finished basements, rec rooms, home gyms, showrooms and offices.

Full answer on Partial Flake Floors →Link to this answer

Should I pick partial flake or solid color?

Partial flake if you want a finished look with some texture that hides a bit of dust. Solid color if you want one plain, even color where a dropped part or a new leak is easy to spot, like a shop or storage room. Solid color is smooth unless grit is added, and it shows dust and tire marks more.

Full answer on Partial Flake Floors →Link to this answer

How much does a partial flake floor coating cost?

Ours is in the same $6–$9 per square foot range as full flake, with a $2,000 minimum; nationally, professional coatings run about $4 to $12 (HomeGuide). Your firm price comes from photos of your floor. The prep, base coat and topcoat are the same as full flake; only the amount of flake changes. We can price both from the same photos so you can compare.

Full answer on Partial Flake Floors →Link to this answer

Solid Color Floors →

What is a solid color floor coating?

A pigmented coating with no flake, in one even color. It gets the same prep as a flake floor and is finished with grit anywhere the floor gets wet.

Full answer on Solid Color Floors →Link to this answer

Does a solid color floor show dirt more than flake?

Yes. With no flake to break up the surface, dust, tire marks and scuffs show more. That's also why some shops prefer it: a dropped part or a new leak is easy to spot.

Full answer on Solid Color Floors →Link to this answer

What colors can I get in a solid color floor?

A range of shades, and we bring real samples, because a color on a screen never matches a floor. Grays are the most forgiving with everyday dirt. Lighter shades hide dust better, while darker ones show dust and scuffs more, so pick with how the room gets used in mind.

Full answer on Solid Color Floors →Link to this answer

Does a solid color floor get a clear topcoat like a flake floor?

Yes. The pigmented color goes on in layers for an even finish, then it gets the same UV-stable polyaspartic topcoat we use on flake floors, which takes the wear and won't yellow by a sunny door or window. Grit goes into that topcoat wherever the floor gets wet.

Full answer on Solid Color Floors →Link to this answer

Is a solid color floor a good idea for a garage?

It works, but most people pick flake for a garage. A solid color shows salt film, dust and tire marks more, and it needs grit in the topcoat for grip with snowmelt on the floor. If you'd rather spot leaks and dropped parts at a glance, a solid color garage with grit is a practical choice.

Full answer on Solid Color Floors →Link to this answer

How much does a solid color floor coating cost?

Ours is $6–$9 per square foot installed, with a $2,000 minimum; nationally, professional floor coatings run about $4 to $12 (HomeGuide). Your firm price comes from photos of your floor and its size, by text within 24 hours. The size, crack and pit repair, and any old paint or sealer that has to be ground off move the number most.

Full answer on Solid Color Floors →Link to this answer

Sealing, cleaning & caulking

Penetrating sealer, pressure washing, and the joint and crack caulking that keeps water out from under a slab.

Concrete sealing →Concrete cleaning →Concrete caulking →

Show Hide 45 questions from 3 pages

Concrete Sealing →

Do you sealcoat asphalt driveways?

No. We seal concrete only: driveways, walks, garage aprons, steps and patios, stamped and decorative concrete included. Asphalt sealcoating is a different product and a different trade.

Full answer on Concrete Sealing →Link to this answer

How often should a concrete driveway be resealed?

When it stops beading water. A penetrating sealer often lasts 5 to 10 years, depending on sun, traffic, plowing and salt. Sprinkle water on it each spring; if it darkens and soaks in, especially in the tire paths, it's time.

Full answer on Concrete Sealing →Link to this answer

How much does concrete driveway sealing cost in Green Bay?

Usually $0.40 to $0.90 per square foot, depending on the sealer and how thirsty the concrete is. Most residential jobs, a driveway plus the walks, apron or patio, land between $640 and $1,000 or more. Cleaning comes first, since sealer only soaks in evenly on clean concrete, and open joints get caulked; it's all one job on one quote.

Full answer on Concrete Sealing →Link to this answer

Do I have to get my concrete cleaned before you seal it?

Almost always. Dirt, oil and salt film keep a penetrating sealer from soaking in evenly, so the slab gets cleaned first and then has to dry, usually at least a day, before the sealer goes on. If yours is already clean enough, we'll tell you from the photos.

Full answer on Concrete Sealing →Link to this answer

How do I get my driveway ready for sealing?

Not much is needed. Once the concrete has been cleaned, keep cars, furniture and grills off it, and turn off any sprinklers that hit it the day before and the day of. Tell us about anything you want protected, like a garden bed or a wood deck along the slab.

Full answer on Concrete Sealing →Link to this answer

How do you apply concrete sealer?

With a low-pressure sprayer or a roller, never a drifting mist. We work in sections, keep a wet edge to avoid lap marks, and put down as much as the label says the concrete should take. Any puddles in low spots or joints get back-rolled or broomed out so the sealer soaks in instead of sitting on top.

Full answer on Concrete Sealing →Link to this answer

Will sealer overspray get on my car, siding or garage door?

It shouldn't. We cover garden beds, mask door thresholds, siding along the slab and the bottom of the garage door, and keep cars, glass, wood decking and any asphalt out of the spray. Low-pressure application, and skipping windy days, keeps the sealer where it belongs.

Full answer on Concrete Sealing →Link to this answer

Should sunken slabs be lifted before the driveway is sealed?

Yes. Sealing over a problem just gives you a sealed problem, so sealing always comes last: clean, dry, lift, patch the drill holes, caulk the joints, then seal once the caulk has cured. It's one booking and one plan, usually over more than one trip, and your quote lays out the schedule.

Full answer on Concrete Sealing →Link to this answer

Can I apply concrete sealer to my driveway myself?

Yes, if you get the prep right: clean it well, wait until it's dry, apply inside the label's temperature range with no rain coming, and work out puddles so it all soaks in. Most DIY sealing fails on dirty or damp concrete, or over an old film sealer it can't soak through. Our guide to choosing a concrete sealer helps with the product.

Full answer on Concrete Sealing →Link to this answer

Is there a guarantee on concrete sealing?

Sealer life depends on sun, traffic, plowing and salt, so we don't promise a set number of years. What we control is the application: clean, dry concrete, the label's conditions and even coverage. Your quote spells out exactly what we stand behind, and if something looks wrong afterward, text us a photo and we'll take a look.

Full answer on Concrete Sealing →Link to this answer

How do I know if my concrete is already sealed?

Sprinkle some water on it. If it beads up and sits on top, there's still sealer working. If it darkens the concrete and soaks in fast, the concrete is bare or the old sealer has worn out.

Full answer on Concrete Sealing →Link to this answer

Will sealer make my driveway slippery?

A penetrating sealer leaves no film, so once it's dry it keeps about the same grip as bare concrete. It can be slick for a few hours while drying. Glossy film-forming sealers are the ones that get slippery when wet, which is why they usually get a grit additive.

Full answer on Concrete Sealing →Link to this answer

How soon can new concrete be sealed?

Once it's cured. The penetrating sealer labels we checked call for 14 to 28 days, and some for a full 28. If your concrete was poured this summer, it's worth getting it sealed before its first winter, as long as the cure time has passed.

Full answer on Concrete Sealing →Link to this answer

Is fall too late to seal in Green Bay?

Early fall is a great time, right before salt season. The catch is temperature: most labels want 40°F or warmer during application and for hours afterward, some for days. A warm October afternoon can still be followed by a cold night, so we push fall sealing toward early fall.

Full answer on Concrete Sealing →Link to this answer

Do I still need my joints caulked if I seal?

Yes. Sealer protects the surface of the concrete. It can't bridge an open joint or crack, and that's where most water gets under a slab. Caulk handles the gaps, and sealer handles the surface.

Full answer on Concrete Sealing →Link to this answer

Concrete Pressure Washing →

Do you pressure wash houses or decks?

No. We clean concrete: driveways, walks, patios, garage aprons, and garage floors before a coating. House and deck washing is a different job with different equipment.

Full answer on Concrete Pressure Washing →Link to this answer

How much does driveway pressure washing cost in Green Bay?

$0.60 a square foot for the first 1,000 square feet and $0.55 for every square foot past that, with a $350 minimum, which covers about a two-car driveway. A driveway, walk and patio together, about 830 square feet, comes to about $498. Booked with caulking or a lift, any cleaning is $50 less. Stain pre-treatment, edges, rinse and runoff control are included.

Full answer on Concrete Pressure Washing →Link to this answer

Should I rent a pressure washer or hire someone to clean my driveway?

For concrete that's just dusty, a hose and a push broom are enough. A rented washer with a narrow tip held close is how driveways end up etched with stripes that never wash out. Hiring it out gets you a rotary surface cleaner for even passes, stain-by-stain pre-treatment, and runoff kept out of the storm drain.

Full answer on Concrete Pressure Washing →Link to this answer

How cold is too cold to pressure wash concrete?

Anything near freezing. We clean above freezing with no hard freeze right behind it, because water left on the slab turns to ice, and wet concrete freezing over and over is a big part of what flakes old Wisconsin driveways. Spring after the snow is gone and late summer into early fall are the best windows.

Full answer on Concrete Pressure Washing →Link to this answer

How soon can new concrete be pressure washed?

Give it about a month. Brand-new concrete under about a month old shouldn't be pressure washed yet. If it just needs construction dust or mud rinsed off in the meantime, a garden hose and a push broom will do it.

Full answer on Concrete Pressure Washing →Link to this answer

Do you keep the wash water out of the storm drain?

Yes. Storm drains run untreated to the nearest creek, river or the bay, and Northeast Wisconsin's regional stormwater guidance says sending wash water down one is prohibited. We sweep up loose dirt first, use only as much cleaner as each stain needs, and steer runoff onto lawn or gravel, blocking the drain when the slope heads that way.

Full answer on Concrete Pressure Washing →Link to this answer

Can you get fertilizer rust stains off my driveway?

Usually most of it. We use a rust remover made for concrete and spot-test it first, since acid-based products can lighten the surface. Spreader marks usually fade a lot, while old rust that's set deep may leave a tint, and your quote will say which kind yours looks like.

Full answer on Concrete Pressure Washing →Link to this answer

Will you tell me if cleaning turns up cracks or sunken slabs?

Yes, because a clean slab shows cracks, open joints, a slab edge sitting higher than the next, and washed-out soil along an edge. We photograph anything we find, show you, and tell you whether it's something to watch, a fix you can handle yourself, or something we can quote. Nothing gets added to your job unless you ask.

Full answer on Concrete Pressure Washing →Link to this answer

What should I move before you pressure wash?

Cars, bikes, grills and furniture, so the whole slab is open. Also check that an outdoor faucet works, close windows and the garage door on the side we're working, and tell us about anything buried at the edge, like a downspout line, lighting wire or sprinkler head.

Full answer on Concrete Pressure Washing →Link to this answer

Will pressure washing damage my concrete?

It can if it's done carelessly. Too much pressure or a narrow nozzle held close etches the surface and leaves stripes. Even passes, lower pressure on edges and weak spots, and the right pre-treatment do the work instead of brute force.

Full answer on Concrete Pressure Washing →Link to this answer

Will every stain come out?

Not always. Fresh oil, mildew, leaf stains, and salt film usually clean up well. Oil that's soaked in for years and rust that's set deep often lighten a lot without vanishing. Your quote will say which of your stains fall into that group.

Full answer on Concrete Pressure Washing →Link to this answer

What do you do to protect my lawn and plants?

We wet plants down before any cleaner goes on, rinse them after, and use only as much cleaner as each stain needs. If there's a bed you're protective of, point it out on the walk-through.

Full answer on Concrete Pressure Washing →Link to this answer

Do I need to be home?

Not for the whole job. It helps if you're around at the start to walk it with us. We'll need a working outdoor faucet either way.

Full answer on Concrete Pressure Washing →Link to this answer

How soon can I seal after you clean?

Once it's dry. Sealer labels typically call for at least a day after washing or rain, and some ask for longer. We go by the label on the sealer we're using.

Full answer on Concrete Pressure Washing →Link to this answer

Do you clean garage floors?

Before a coating, yes. Oil soaked into a garage floor keeps a coating from bonding, so degreasing is part of getting the floor ready. For a floor that's just dirty, a stiff broom, a store-bought degreaser, and a hose usually do the job without us.

Full answer on Concrete Pressure Washing →Link to this answer

Crack & Joint Caulking →

How long does joint sealant last?

Several years in most cases, depending on how much the slabs move and how much sun the joints get. We recommend a quick look every few years and touching up any section that has pulled away.

Full answer on Crack & Joint Caulking →Link to this answer

Can you seal cracks as well as joints?

Yes. Cracks get cleaned out and filled with the same flexible sealant, so water can't get under the slab through them.

Full answer on Crack & Joint Caulking →Link to this answer

Do I need sealing if I'm getting my concrete lifted?

We recommend it. Lifting fixes the result of water getting under the slab; sealing stops the cause. Together they keep the concrete level far longer.

Full answer on Crack & Joint Caulking →Link to this answer

Is there any maintenance after concrete is lifted?

A little, and it matters. Keep the joints and cracks sealed so rain and snowmelt can't get under the slab, and touch up any sealant that pulls away. If the lift left a slab edge standing above the soil, backfill against it with topsoil so the base stays covered. And keep downspouts discharging several feet from any slab. Those three things stop the water that put the slab there in the first place.

Full answer on Crack & Joint Caulking →Link to this answer

How much does concrete joint caulking cost in Green Bay?

Usually $5 to $10 per linear foot, depending on joint size, how much old caulk or rotted wood comes out, and backer rod. Booked on its own, caulking has a $275 minimum, about 4 to 6 sidewalk joints or up to about 30 feet; added to a lift, you just pay the footage. A driveway with 10 or more joints, or 100-plus feet, can reach $1,000 or more.

Full answer on Crack & Joint Caulking →Link to this answer

How do you figure out how many feet of joint I have?

From your photos: a wide shot of each area shows the joint layout, and a few close-ups with a tape measure across the gap show the widths. If you know roughly how long the driveway is or how many slabs it has, include it. As a rough check, 60 feet of joint at $5 to $10 a foot comes to $300 to $600.

Full answer on Crack & Joint Caulking →Link to this answer

Do you remove the rotted wood strips from my driveway joints?

Yes. Rotted wood and soft fiberboard come out completely, along with sand, weeds and roots, then each joint is wire-brushed, vacuumed, fitted with backer rod and sealed. Pulling old strips takes longer than sealing clean, open joints, so it moves a driveway toward the higher end of the per-foot price.

Full answer on Crack & Joint Caulking →Link to this answer

Is there anything I need to do before you caulk the joints?

Move cars, grills and planters off the joints, and don't pressure wash the concrete the day before. Washing soaks the joints, and they have to be dry before any sealant goes in. If you've booked cleaning too, it goes first, and we give the joints time to dry out before we caulk.

Full answer on Crack & Joint Caulking →Link to this answer

When is caulking not the right fix?

When one side of the joint has dropped: caulk over an offset seals the hollow in underneath, so that slab gets lifted first. When the joint edges are crumbling or the slab is broken into pieces, because sealant needs solid concrete to grip and edge repair isn't our work. We'll tell you from the photos, even if it means you don't hire us.

Full answer on Crack & Joint Caulking →Link to this answer

How long will you be at my house?

It depends on how many feet of joint you have and how much old material has to come out. Sealing clean, open joints goes quickly. Pulling rotted wood strips or cutting out old caulk takes longer. Your quote will give you a realistic idea.

Full answer on Crack & Joint Caulking →Link to this answer

What happens if it rains on caulking day?

We move the job. Sealant laid in a damp joint doesn't bond, and rain before the bead skins over can ruin it. We'd rather lose a day than do it twice.

Full answer on Crack & Joint Caulking →Link to this answer

Can I drive on my driveway after you seal the joints?

Not over the fresh beads until the label says it's ready for traffic. We'll tell you how long before we leave and mark the joints so they're easy to avoid.

Full answer on Crack & Joint Caulking →Link to this answer

Will the caulk match my concrete?

It'll be close, not invisible. We don't stock a fixed set of colors: for each job, we buy the sealant color that best matches your concrete. A sealed joint still reads as a joint line, though. Most people find it looks a lot better than a dark, weedy gap.

Full answer on Crack & Joint Caulking →Link to this answer

Is it too late in the year to caulk?

Not if it's still at least about 40°F during the day and the concrete is dry and frost-free. Once the ground starts freezing for the season, we wait until spring.

Full answer on Crack & Joint Caulking →Link to this answer

How do I know when my joints need resealing?

Look for a bead that's split down the middle, pulled away from one side, turned hard and cracked, or has weeds growing past it. Check every spring, and reseal before the next winter.

Full answer on Crack & Joint Caulking →Link to this answer

Pricing & cost

What the work costs, how a price is built, the job minimum, and how the calculator gets its numbers.

Pricing →Concrete leveling cost in Green Bay →

Show Hide 21 questions from 4 pages

Pricing →

Can you give me a price from photos?

Yes, for most jobs. Send a wide photo, a close-up with a tape measure showing how far the slab dropped, and a shot along the slab. You'll get a firm price by text or email within 24 hours. We only visit when the photos can't answer something.

Full answer on Pricing →Link to this answer

Do you offer financing?

Ask when you request your price. Most leveling jobs are small enough that people pay on completion, and we'll tell you the payment options with your quote.

Full answer on Pricing →Link to this answer

Can I save by bundling with neighbors?

Yes. Travel and setup are a big part of a small job's price. When two or more neighbors book together, we do them in one trip and share the savings.

Full answer on Pricing →Link to this answer

Concrete Leveling Cost →

How much does concrete leveling cost in Green Bay?

Our foam lifting jobs start at $300. A single panel or AC pad runs $300–$600, a garage apron or one driveway section $400–$1,000, a patio $600–$1,500, and two or three driveway sections $800–$3,000. Nationally the average leveling job is about $1,241 (HomeAdvisor, 2026).

Full answer on Concrete Leveling Cost →Link to this answer

Why does concrete leveling cost so much?

On average it costs about half of tearing out and replacing the old sunken concrete. The foam is what sets the price: it's a specialized two-part polyurethane that's expensive to buy, and a slab with more empty space under it takes more of it.

Full answer on Concrete Leveling Cost →Link to this answer

Is there a minimum charge for concrete leveling, and why?

Yes, like almost every lifting company. Travel, setup, cleanup and the material in the hoses cost the same for one small section as for several, so a minimum keeps small jobs worth doing.

Full answer on Concrete Leveling Cost →Link to this answer

Do you charge per slab, per inch or per pound of foam?

We charge by the material the job takes. How far the slab has sunk, the void under it and the size of the slab set how much foam that is, and on average it comes to $4–$10 per square foot. You get a firm price before we start. If we ever find a much bigger void than expected, we stop and talk with you before going further.

Full answer on Concrete Leveling Cost →Link to this answer

What's included in the price, and what's extra?

Lifting, hole patching, cleanup and photos are included. Joint and crack sealing is listed as its own line on the quote so you can choose it. Moving heavy items off the slab is up to you.

Full answer on Concrete Leveling Cost →Link to this answer

Garage Floor Coating Cost →

How much does it cost to coat a two-car garage?

With us, about $2,400–$3,600 for a 400-square-foot two-car garage and $3,456–$5,184 for a larger 576-square-foot one, at $6–$9 per square foot. Nationally it's about $1,600 to $4,800 and $2,300 to $6,900 (HomeGuide). Send a photo of the floor and its size for a firm price by text or email, usually within 24 hours.

Full answer on Garage Floor Coating Cost →Link to this answer

Is there a minimum for a floor coating?

Yes, $2,000. It covers the setup, grinding and dust extraction that every floor needs, so a small floor still gets the full system. A one-car garage of about 288 square feet already runs $2,000–$2,592.

Full answer on Garage Floor Coating Cost →Link to this answer

Why are professional garage floor coatings more expensive than DIY kits?

Diamond grinding, crack repair and a thicker multi-layer system cost more than an etch-and-roll kit. Those are exactly what keep a coating from peeling under hot tires and road salt.

Full answer on Garage Floor Coating Cost →Link to this answer

Does the price include moving everything out of the garage?

The floor has to be completely empty. Most people move their own things; if you'd rather we handle it, ask and we'll quote it.

Full answer on Garage Floor Coating Cost →Link to this answer

How many square feet is a garage?

A one-car garage is usually about 288 square feet (12 by 24 feet), a two-car 400 to 576 (20 by 20 up to 24 by 24), and a three-car about 864 (24 by 36). Measure wall to wall at the floor and multiply length by width.

Full answer on Garage Floor Coating Cost →Link to this answer

Does full flake cost more than partial flake or solid color?

No. All three finishes are in the same $6–$9 per square foot range with the same $2,000 minimum, because the grinding, the repairs, the base coat and the topcoat are the same. Only the amount of flake changes. We can price more than one finish from the same photos so you can compare.

Full answer on Garage Floor Coating Cost →Link to this answer

What does it cost to grind off an old garage floor coating first?

It's priced on top of the per-square-foot rate, and the number is on your quote before you decide. Paint, old epoxy and sealers have to be ground off completely, because a new coating is only as strong as what's under it. Send a close-up of the old coating, especially anywhere it's peeling, with your other photos.

Full answer on Garage Floor Coating Cost →Link to this answer

Is a garage floor coating priced by the square foot or by the garage?

By the square foot: $6–$9 installed, never under the $2,000 minimum. The one-, two- and three-car prices on this page are that rate times a typical floor area, so a garage that's bigger or smaller than those sizes is priced on its own measurements.

Full answer on Garage Floor Coating Cost →Link to this answer

Leveling Cost Calculator →

How accurate is the concrete leveling cost calculator?

It uses the same published sheet our quotes start from: the job ranges and $4–$10 per square foot, never under the $300 minimum. Most jobs land inside the range it shows. The firm price comes from three photos, because the one thing the calculator can't see, the empty space under the slab, is what moves a job to the top of its range.

Full answer on Leveling Cost Calculator →Link to this answer

Is this a mudjacking cost calculator too?

Yes, for the same jobs. We lift with polyurethane foam rather than a cement slurry, which is why the holes are 5/8 inch instead of 1½ to 2 inches and why you can use the slab the same day. The job types and the pricing logic (sections, drop, access) are the same ones a mudjacking contractor would quote; only the material differs.

Full answer on Leveling Cost Calculator →Link to this answer

Why does the calculator never go below the job minimum?

Travel, setup and cleanup cost about the same whether we lift one sidewalk square or six driveway sections, so every job carries the $300 minimum. Small jobs often make sense to bundle: a sunken step and two low walk panels in one visit cost less than two trips.

Full answer on Leveling Cost Calculator →Link to this answer

Does the calculator price include sealing the joints?

No. Joint and crack caulking is quoted by the linear foot ($5–$10) and usually added right after the lift, with no separate minimum on a combined visit. It's the step that keeps the water that caused the sink from washing the base out again.

Full answer on Leveling Cost Calculator →Link to this answer

What if the calculator says lifting costs more than I expected?

Compare it with replacement before deciding. On average a lift costs about half of tearing out and pouring new concrete for the same area. New concrete also takes about a week before you can drive on it, and it sits on the same soil that let the old slab down. Send the photos anyway: a slab over a small void sometimes prices below its range, and we'll say so.

Full answer on Leveling Cost Calculator →Link to this answer

Businesses, warranty, referrals & guides

Commercial and HOA work, the referral program, and our guides to measuring a sunken slab, spring checks and why concrete sinks here.

Commercial & HOA →Warranty →Learn →

Show Hide 39 questions from 6 pages

Commercial & HOA →

How long does a business entrance need to be closed for lifting?

Usually only while we're working on it, often an hour or two per area. The foam sets in minutes and hole patches set quickly, so the area can reopen the same day.

Full answer on Commercial & HOA →Link to this answer

Do you provide documentation for insurance or HOA records?

Yes. Every location gets before-and-after photos and the measured change, so you have a record that the hazard was found and fixed.

Full answer on Commercial & HOA →Link to this answer

Can you handle multiple properties?

Yes. Send a list of addresses and problem areas, or we walk them, and you get one priced list by location to approve.

Full answer on Commercial & HOA →Link to this answer

How much does it cost to fix a trip hazard at our business in Green Bay?

Usually $300 to $600 for one sunken walk panel, and $300 is our lifting minimum. Larger jobs run about $4 to $10 per square foot, so several problem areas lifted in one visit (300 to 400 square feet) typically land at $1,200 to $4,000. Joint caulking adds $5 to $10 per linear foot, with no separate minimum alongside a lift.

Full answer on Commercial & HOA →Link to this answer

Will lifting bring our walk within the ADA 1/4-inch limit?

That's the goal on a sunken slab: we lift the low panel flush with its neighbor, which removes the change in level instead of beveling around it, and restores the slope if settling tipped it. Lifting can't widen a narrow walk, fix one poured too steep or lower a heaved panel. More in our ADA sidewalk guide.

Full answer on Commercial & HOA →Link to this answer

Does Wisconsin's safe-place law cover our sidewalks and entrances?

It can: Wisconsin's safe-place statute (Wis. Stat. 101.11) holds employers and owners of public buildings to a higher duty than ordinary negligence to keep their property safe. How it applies to your walk is a question for your attorney or insurance carrier. Our part is fixing the hazard and giving you before-and-after photos and measurements.

Full answer on Commercial & HOA →Link to this answer

We just got a complaint about a trip hazard. How fast can you help?

Send photos today: a wide shot and a close-up with a tape measure standing at the lip. You'll get a firm price by text or email within 24 hours, and we'll fit it in as soon as the schedule and weather allow, early or after hours if needed. Until then, cone it or paint the edge a bright color and log the date.

Full answer on Commercial & HOA →Link to this answer

Can you work before we open, after we close, or around services and events?

Yes, early-morning and after-hours starts can be arranged when an entrance, drive-thru or church walk can't be blocked while you're open. We work one section at a time where we can, and a lifted section carries foot traffic as soon as we pack up. Tell us your hours, deliveries and events when you send photos.

Full answer on Commercial & HOA →Link to this answer

Can our board approve part of the list now and the rest later?

Yes. Every spot gets its own priced line, with its location and measured lip, so the board can approve the worst ones now and hold the rest for a later phase or next year's budget. Lifting several spots in one visit does cost less per spot than spreading them out.

Full answer on Commercial & HOA →Link to this answer

Can you meet our vendor requirements, like a certificate of insurance and a W-9?

Send what your vendor setup needs with the photos, such as a certificate of insurance, a W-9 or a purchase order number, and we'll provide it with the quote and invoice in the name of whoever pays: the owner, the association or the management company.

Full answer on Commercial & HOA →Link to this answer

Can you walk our property every spring and flag new trip hazards?

Yes. A spring walk after the frost is out, with photos and a measurement at every lip, gives you a record and a priced list for the season. Spots under 1/4 inch go on a watch list to remeasure the next year, so you can budget for them before they become a hazard.

Full answer on Commercial & HOA →Link to this answer

A walk dropped or heaved over the winter. What do we do until spring?

Cone it or paint the edge a bright color, log the date, and send us photos. We can't lift on frozen ground, so you'll get a price and a spot on the spring schedule. A slab that heaved may settle back once the ground thaws, so we measure again in spring before lifting anything.

Full answer on Commercial & HOA →Link to this answer

Can you clean and seal our walks too, not just lift them?

Yes, on concrete. On a combined job we clean first, let it dry, lift, patch the holes, caulk the joints and the gap at the building, then seal once the caulk has cured. Wash water stays out of the storm drain, and booking it all together can lower the overall price.

Full answer on Commercial & HOA →Link to this answer

Are you set up for large commercial properties?

We're a small, owner-operated crew, which suits storefronts, restaurants, offices, churches, small strip centers and shops with a handful of problem areas. If you have a campus-sized list, send it anyway. We'll tell you honestly what we can take on and when, rather than overbook.

Full answer on Commercial & HOA →Link to this answer

Do commercial lifts come with a warranty?

Yes. The written warranty on your quote spells out what's covered before you approve it, so it can go in the file with the work order. If a lifted section moves, text us a photo with a tape measure and we'll take a look.

Full answer on Commercial & HOA →Link to this answer

Why Concrete Sinks in NE Wisconsin →

Is sinking concrete a sign of a foundation problem?

Usually not. Driveways, walks and patios sit on shallow soil, while Wisconsin's building code puts house footings at least 48 inches below grade, below the frost line. A sunken slab next to the house is almost always settled backfill, not foundation movement. Cracks in the foundation walls themselves are a different question for a foundation specialist.

Full answer on Why Concrete Sinks in NE Wisconsin →Link to this answer

Why does new concrete sink?

Newer homes often have driveway aprons, walks and stoops sitting on backfill from the basement dig. That fill settles for several years after construction, and the concrete on top settles with it.

Full answer on Why Concrete Sinks in NE Wisconsin →Link to this answer

How to Measure & Photograph It →

Do I need a level or special tools to measure sunken concrete?

No. A tape measure and your phone cover most jobs: stand the tape upright at the lowest edge, next to the slab that didn't move, and take the picture. A straight board or a level only helps when a slab has tipped instead of dropping at a joint, so you can measure the gap under the far end.

Full answer on How to Measure & Photograph It →Link to this answer

What if I can't tell how far my concrete dropped?

Pick "Not sure" on the form and send the tape-measure photo anyway. We read the drop from the tape in the picture. The form only asks for a range, such as 1 to 2 inches, so a rough number is all it needs.

Full answer on How to Measure & Photograph It →Link to this answer

How many photos can I send with a quote request?

Up to 8 on the form, and three price most jobs: a wide shot, the tape measure at the lowest edge, and one along the slab. If you have several areas and need more room, text the rest to (920) 655-2193.

Full answer on How to Measure & Photograph It →Link to this answer

Do you need my slab's square footage for a lifting quote?

No. The form asks how many sections are low and about how far the lowest spot dropped, and the wide shot lets us size the rest. If you know the dimensions, include them. Lifting has a $300 minimum, and larger jobs run about $4–$10 per square foot.

Full answer on How to Measure & Photograph It →Link to this answer

What if my photos aren't enough to price the job?

We'll ask before we quote, usually for one more photo or a measurement. A site visit only happens when the photos can't answer something, like a hollow porch that needs a closer look.

Full answer on How to Measure & Photograph It →Link to this answer

Spring Concrete Checklist →

What tools do I need for a spring concrete walk-around?

A phone, a tape measure and a level. The phone is for photos, the tape is for the height of any lip at a joint, and the level shows whether a patio, walk or stoop tips toward the house. Tapping a slab corner with a screwdriver handle helps too: a hollow sound points to an empty space underneath.

Full answer on Spring Concrete Checklist →Link to this answer

How do I know if a slab moved over the winter or was always that way?

Photos. Take them from the same spots every spring and compare year over year; it's the easiest way to tell whether something is moving. Without old photos, look for fresh signs: caulk that's newly torn, a lip the snowblower started catching, or water standing where it didn't last year.

Full answer on Spring Concrete Checklist →Link to this answer

Which spring concrete problems can wait, and which can't?

Fix a trip lip over 1/4 inch, a patio or walk that tips toward the house, and any downspout that empties at a slab; those get worse or put water at the foundation. Seal open joints before the next winter. Hairline cracks with no height change can be sealed and watched, and a frost-heaved slab that settled back needs drainage fixes, not lifting.

Full answer on Spring Concrete Checklist →Link to this answer

Is a puddle on my driveway after rain a problem?

It can be. Water still standing a few hours after rain marks a low spot. Near the garage door or the foundation, it usually means a section sank or tipped and is holding water where you least want it, so that one is worth fixing. Take a photo while the puddle is there; it shows exactly where the low spot is.

Full answer on Spring Concrete Checklist →Link to this answer

Should I book spring concrete repairs before the ground thaws?

Yes, for lifting. Send photos as soon as you spot the problem and you'll have a price in hand; the lift itself happens once the frost is out, because we don't lift on frozen ground. Re-measure after the thaw, though, since a slab that heaved over the winter can settle back on its own.

Full answer on Spring Concrete Checklist →Link to this answer

Warranty →

How long is the concrete leveling warranty?

5 years from the day we lift the slab. If a slab we lifted settles again in that time, we come back and re-lift it at no charge.

Full answer on Warranty →Link to this answer

Is the warranty in writing?

Yes. The warranty terms for your job are printed on your quote in plain language, so you read them before you approve anything.

Full answer on Warranty →Link to this answer

What do I have to do to keep the leveling warranty in force?

Two things, and both keep water out from under the slab: keep the joints and cracks along the lifted slabs sealed, and keep your downspouts extended so roof water drains away from the concrete. We can caulk the joints on the same visit as the lift.

Full answer on Warranty →Link to this answer

Does the leveling warranty cover frost heave?

No. Frost can push a slab up in winter and let it settle back in spring, and that movement comes from the ground freezing, not from the lift. The warranty covers a lifted slab that settles again.

Full answer on Warranty →Link to this answer

Does the warranty cover cracks that show up after a lift?

No. A lift raises the slab; it doesn't make old concrete new. New cracks, and concrete that breaks or crumbles, aren't covered. If a section looks too broken to promise, your quote says so before you approve it.

Full answer on Warranty →Link to this answer

How do I make a warranty claim?

Text a photo of what you're seeing, with a tape measure in it if a slab has moved. We look at the photo first and come out if we need to. If it's covered, we fix it. If it isn't, we explain why and what your options are.

Full answer on Warranty →Link to this answer

How long is joint and crack caulking covered?

Up to one year. Wisconsin winters are hard on caulk, so walk your joints each spring and tell us if a bead has split or pulled away.

Full answer on Warranty →Link to this answer

Referral Program →

Do I have to be a customer to refer someone?

No. Anyone can refer: customers, neighbors, realtors, property managers, contractors. If the person you send books and we finish their job, you get the gift card.

Full answer on Referral Program →Link to this answer

When do I get the referral gift card?

Within two weeks of the referred job being completed and paid. We text you to ask where to send it.

Full answer on Referral Program →Link to this answer

How much is the referral gift card?

$100 for a referred job under $1,500, and $200 for a job of $1,500 or more. It goes by the final bill, so if their job grows (say they add caulking or a second area), your gift card can too.

Full answer on Referral Program →Link to this answer

Does my neighbor get anything for being referred?

They get the same honest price-from-photos process as everyone else, and if we can do both of your properties in one trip, both of you share the savings on the trip charge. Ask about the neighbor bundle when you send photos.

Full answer on Referral Program →Link to this answer

Can I refer a business or an HOA?

Yes. Commercial and HOA jobs count the same way: once the work is completed and paid, you get the gift card for that completed job.

Full answer on Referral Program →Link to this answer

In our articles

486 more answers in our articles →
Cracks, caulking, cleaning, sealing, drainage, ADA rules and more. Each article ends with its own questions.

Get your price from a few photos

Send three phone photos and a quick measurement. You'll get a firm price by text or email within 24 hours, no site visit needed for most jobs.

Get My PriceCall (920) 655-2193