Skip to content
(920) 655-2193|Serving Green Bay & Northeast Wisconsin
Rise & Grind Concrete
Get My Price
Mudjacking · Green Bay

Mudjacking in Green Bay? Why We Lift With Polyurethane Foam

The short answer

If you're searching for mudjacking in Green Bay, the job you want done is lifting a sunken slab back to level. We do it with polyurethane foam, often called polyjacking: the same idea as mudjacking, but through 5/8-inch holes instead of 1½ to 2-inch ones, with material that weighs about 2 to 5 pounds per cubic foot instead of 100 to 150. You can walk on it right away.

By Rob Diederich, owner · Updated
Holes
5/8 in, not 1½–2 in
Weight under the slab
2–5 lb/ft³, not 100–150
Use it
Same day
Quote
From photos, within 24 hours

Mudjacking, slabjacking, polyjacking: the same job

Mudjacking (some write it mud jacking) is the most-searched name for this work around Green Bay, and plenty of people use it to mean any slab lifting. If that's what you searched, you're in the right place: the job is the same, the material under the slab is different.

Mudjacking, slabjacking, concrete jacking, concrete raising, polyjacking and concrete leveling in Green Bay all mean the same thing: filling the space under a sunken slab and using that fill to push the slab back up. The difference is what goes under it. Mudjacking pumps a cement-and-soil slurry through large holes. We use two-part polyurethane foam, which goes in as a liquid through small ports and expands under the slab.

What mudjacking is and how it works

Mudjacking is the older way to raise a sunken slab, and the idea is simple: pump enough material under the concrete to fill the empty space, then keep pumping until the slab comes up.

  1. 1Drill.Holes about 1½ to 2 inches wide are drilled through the slab.
  2. 2Pump the slurry.A slurry of soil or sand, cement and water goes in through the holes. Some mixes add lime, fly ash or clay. It's thick, gritty and heavy: about 100 to 150 pounds per cubic foot.
  3. 3Lift.The slurry fills the space under the slab, and the pump pressure raises it.
  4. 4Patch and wait.The holes get patched and the slurry sets into a hard, cement-like fill. Cars usually stay off for 24 to 48 hours.

Foam lifting follows the same steps with a different material: dime-sized 5/8 inch holes, foam that weighs about 2 to 5 pounds per cubic foot, and a slab you can drive on the same day. How foam concrete lifting works walks through it.

When mudjacking is a legitimate choice

We don't offer mudjacking, and we won't pretend it doesn't work. It's the older method, but on dry, stable ground without a water problem it can hold up well, and it usually costs less upfront, because soil, sand and cement cost a fraction of what lifting foam does. It's a reasonable pick for:

  • A sidewalk square out by the street, on firm, dry ground, where the lowest price wins. Weight and washout matter less on stable soil.
  • A large washout under a big slab, on firm ground, with a tight budget. Material is a bigger share of a foam quote there, so get quotes for both.
  • Anyone who'd rather not have plastic in the ground. Mudjacking slurry is a mineral fill: soil, sand and cement.

Where it struggles is weight and water: next to the foundation, over soft or wet clay, under an AC pad, inside a garage, or anywhere a downspout has been dumping. Those are the jobs where foam is usually worth the extra money. If mudjacking would serve your slab just as well for less, we'll tell you that from your photos. The full head-to-head is in foam vs. mudjacking.

Polyjacking vs. mudjacking: why we use foam

Foam (what we use)Mudjacking
Hole sizeAbout 5/8 inchAbout 1½–2 inches
Weight added to the soilAbout 2–5 lb per cubic footAbout 100–150 lb per cubic foot
Ready for carsSame dayUsually 24–48 hours
Where water runs under the slabWon't wash outCan erode over time
Foam figures from manufacturer data sheets; slurry figures from HD Foundation Repair. The full comparison, costs included, is in foam vs. mudjacking.
Mudjacking: heavy slurryMudjackingFoam: light, waterproofFoam
3D render, simplified. Left: mudjacking slurry through a 2-inch hole. Right: foam through a 5/8-inch hole. When water runs in later, slurry can wash out; foam stays put.
Foam: about 5/8"Roughly dime-sizedMudjacking: about 1-1/2" to 2"Dashed ring = 1-1/2", solid = 2"DRAWN TO SCALE
DRAWN TO SCALEFoamabout 5/8"Roughly dime-sizedMudjackingabout 1-1/2" to 2"Dashed 1-1/2", solid 2"
Hole size to scale: a dime-sized 5/8 inch foam port next to a mudjacking hole of about 1½ to 2 inches.

Northeast Wisconsin slabs mostly sink because water washed the soil out or loose backfill settled. Heavy slurry adds load to that same weak soil; foam barely adds any, and it doesn't wash out the next time water gets under the slab.

3D render, not a job video. It's a generic example, a driveway slab that sank at the garage door; the steps are the same on any slab. The ground is cut away so you can see under the slab; nothing is dug on a real job. Simplified to four ports; a real 10 by 10 foot section usually gets six to ten. The foam's weight, strength and set time, with sources, are in how foam lifting works.

Transcript: what the video shows (23 seconds, no sound)
  1. 1. Set the line. A laser line off the slab that didn't move shows how far the low one has to come up. This one sank about 2″, a little more at the corner.On screen: About 2″ low; Laser line = target; Empty space under the slab.
  2. 2. Drill and set the ports. 5/8″ holes, kept in from the edges, then a plastic injection port tapped into each one so the gun can lock on.On screen: Injection ports.
  3. 3. Pump the foam. Two liquids travel down separate hoses and mix in the gun. They go in through the first port and run to the lowest spots.On screen: Liquid runs to the low spots.
  4. 4. Expand and fill. Within seconds the mix expands 15 to 22 times its liquid volume and fills most of the space from that port. The next port fills the rest, pressing loose soil tight.On screen: Expands from the first port; Second port fills the rest.
  5. 5. Lift to the line. Once the space is full, short shots, port to port, raise the slab evenly. We stop when it meets the line.On screen: Short shots, port to port; Back on the line.
  6. 6. Patch and caulk. The ports come out, each hole is packed with grout and troweled flush, and the joint at the garage gets a bead of flexible sealant.On screen: Garage joint caulked.

Why the fill matters in Green Bay soil

Much of the Green Bay area sits on clay and silt that hold water and drain slowly, so the ground under a slab stays wet long after every rain and thaw. Three local conditions matter:

  • Slow-draining clay. A light fill that doesn't soak up water counts for more on ground that stays wet.
  • Loose backfill along the house. Stoops, patios, walks and AC pads next to the foundation sit on soil that was pushed back in after the basement was dug. It's the softest ground on most lots, and the worst place to stack heavy fill.
  • Spring melt and frost. Snowmelt soaks that backfill, which is why so many sunken slabs show up in April and May. Wet soil also heaves when it freezes, and neither mudjacking nor foam stops that, so a slab that only looks off in late winter waits until the ground thaws.

Whatever goes under the slab, seal the joints and move the downspouts, or the soil around any fill keeps washing out. More in why concrete sinks in Northeast Wisconsin.

What to ask a mudjacking contractor in Green Bay

If you're calling around for mudjacking near you, these questions sort out any leveling quote, ours included:

  • What goes under the slab, and what does it weigh? Slabjacking and concrete raising are general terms that can mean cement slurry or foam.
  • When can I park on it? Mudjacked slabs usually need 24 to 48 hours before cars. A foam lift is ready the same day.
  • Is the price fixed for the job? Or does the bill depend on how much material goes in?
  • What sank it, and what should I fix? If nobody tells you, you'll be doing this again whichever method you pick.
  • Is joint sealing included? Caulking the joints and cracks keeps water from getting back under the slab, whatever fill is down there.
  • What happens if it settles again? Ask for the warranty in writing, and what conditions come with it.

For vetting the company itself, see how to choose a concrete contractor.

What we lift

Driveways and garage aprons →

Sunken sections, the lip at the garage door, water pooling against the house.

Sidewalks and walkways →

Trip hazards at the joints, sections that hold puddles.

Patios →

Slabs that tipped toward the house and send rain at the foundation.

Steps, stoops and porches →

Stoops pulled away from the wall, porches settled under the roof.

Was your slab mudjacked before?

Old mudjacking jobs often settle again where water got under the slurry. Foam can usually go in around or through the old material, and the old large holes get patched while we're there.

Mudjacking cost vs. foam lifting cost

National cost guides put mudjacking at about $3 to $6 per square foot and foam lifting at about $5 to $25. Every slab is different, so we price from photos: send a few and you get a firm price for the foam job. See concrete leveling cost in Green Bay for what goes into it.

We don't mudjack, so we can't quote it. What we can publish is our own foam price sheet:

Foam lifting jobOur price
Single sidewalk panel, AC pad or small stoop$300–$600
Front walk, 3–5 panels (50–125 sq ft)$300–$1,250
Garage apron, approach or one driveway section (about 100 sq ft)$400–$1,000
Patio, 1–2 slabs (about 150 sq ft)$600–$1,500
2–3 driveway sections (200–300 sq ft)$800–$3,000
Several areas in one visit (300–400 sq ft)$1,200–$4,000
Mid-size and larger jobs, rule of thumbAbout $4–$10 per sq ft
Foam lifting prices; every job has a $300 minimum. Your exact price comes from photos, and the concrete leveling cost calculator shows a range for your job in about 30 seconds.

The warranty on a foam lift

Every lift comes with a 5-year written warranty: if a slab we lifted settles again, we come back and re-lift it at no charge, as long as the joints stay sealed and the downspouts drain away from the concrete. The terms are on your quote before you approve it. A slab that was mudjacked before is covered the same way. See the warranty page for how it works.

Have a mudjacking quote? See what foam would cost
Send it with three photos. Firm foam price for the same slabs by text within 24 hours.
Get My Price

Sources

  1. Alchemy-Spetec AP Lift 435 technical data sheet (lifting foam)
  2. Prime Resins Precision Lift 475 technical data sheet (lifting foam)
  3. HD Foundation Repair: mudjacking vs. polyurethane foam
  4. HomeAdvisor: concrete leveling and mudjacking cost (updated June 2026)
Questions

Common questions

Do you do mudjacking in Green Bay?

We lift sunken concrete with polyurethane foam rather than mud slurry. It's the same job, raising a slab by filling the space under it, done through smaller holes with a material that weighs far less and doesn't wash out.

Is polyjacking the same as mudjacking?

Same goal, different material. Polyjacking uses expanding polyurethane foam through holes about 5/8 inch wide; mudjacking pumps a cement-and-soil slurry through holes about 1½ to 2 inches wide.

Can foam lift a slab that was mudjacked before?

Usually, yes. Foam can be injected around or through the old slurry, and the old large holes get patched. If the slab sank again because water is getting under it, we'll point out the downspout or open joint that's doing it.

What is mudjacking?

Mudjacking is the older way to raise sunken concrete. Holes about 1½ to 2 inches wide are drilled through the slab, and a slurry of soil or sand, cement and water is pumped underneath until the pressure lifts it. We do the same job with polyurethane foam, which goes in through 5/8-inch holes and lifts by expanding.

How much does mudjacking cost in Green Bay?

We don't mudjack, but national cost guides put it at about $3 to $6 per square foot. Our foam lifting has a $300 job minimum: a single sidewalk panel or small stoop runs $300 to $600, a garage apron or one driveway section $400 to $1,000, and larger jobs about $4 to $10 per square foot.

My quote says slabjacking. How do I know if that means mud or foam?

Ask, and look at the hole size: slabjacking is a general term that can mean either method. A cement-and-soil slurry needs holes about 1½ to 2 inches wide, while foam goes in through holes about 5/8 inch wide. While you're asking, find out what the fill weighs, whether the quote is a firm price for the job, and what the written warranty covers.

Does the weight of mudjacking slurry really matter?

On soft ground, yes. A 10-by-10-foot slab with 2 inches of empty space under it takes about 17 cubic feet of fill: roughly 1,700 pounds of slurry at about 100 pounds per cubic foot, or around 50 to 100 pounds of foam. That weight lands on the soil that already let the slab sink, as our foam vs. mudjacking guide explains.

Do I have to keep my car off the driveway for two days, like with mudjacking?

No. Mudjacked slabs usually need 24 to 48 hours before cars. Foam reaches 85 to 90 percent of its strength in about 15 minutes, so you can walk on the slab as soon as we pack up and drive on it the same day, once the hole patches have set.

Will foam wash out the way mudjacking can?

No. Cured foam is closed-cell, so it doesn't soak up water or erode the way a cement-and-soil slurry can when water keeps running under a slab. Water can still wash out the soil around any fill, though, so seal the joints and move downspouts away from the slab whatever is underneath.

Why did my mudjacked slab sink again?

Usually water. Rain or snowmelt getting under the slab through an open joint, or from a downspout dumping beside it, can erode the slurry and the soil around it, and the heavy fill adds load to soil that was already soft. We'll point out the likely source on your photos, lift the slab with foam, and seal the joints.

How can I tell if my slab was mudjacked before?

Look for round patches about 1½ to 2 inches across, usually several per slab and often a different shade than the concrete around them. Foam lifting leaves smaller patches, about 5/8 inch. If you're not sure, send a close-up with a tape measure for scale and we'll tell you what we see.

Do you drill new holes or reuse the old mudjacking holes?

New ones: we drill our own 5/8-inch holes, about 3 to 4 feet apart, wherever the foam needs to go. Old mudjacking holes that have loosened or opened up get patched while we're there. Sound old patches stay as they are and will still show.

Can mudjacking be done inside a garage or basement?

It's possible, but it's messy: big holes, slurry hoses and gritty fill inside the building. Foam suits interior slabs better, with 5/8-inch holes, little mess and a floor that's back in use the same day. Before we drill indoors, we need to know about floor drains and any in-floor heat.

Can you compare your price with a mudjacking quote I already have?

Yes. Send it with your photos and you'll get a firm foam price for the same slabs, lifted to the same height, by text within 24 hours. Check that both quotes include joint sealing, and if mudjacking would serve your slab just as well for less, we'll say so.

Do you warranty a lift on a slab that was mudjacked before?

Yes, every lift does, old mudjacked slabs included: the written warranty on your quote spells out what's covered before you approve anything. If water is still getting under the slab, we'll point out what to fix so the lift has the best chance of staying put.

Keep reading

Related

Concrete leveling · Comparison
Foam vs. Mudjacking

Foam vs. mudjacking by the numbers: hole size (5/8 vs 1½–2 in), weight (2–5 vs 100–150 lb/ft³), cure time and national cost per square foot.

Polyurethane foam lifting
Concrete Leveling

Sunken sidewalk, driveway, patio or steps? We lift concrete with foam through dime-size holes. Drive on it the same day. Send photos for a free quote.

Pricing · Concrete leveling
Concrete Leveling Cost

Concrete leveling cost in Green Bay: our foam lifting prices by job, from a $300 minimum, next to national averages, and what moves the price.

Get your price from a few photos

Send three phone photos and a quick measurement. You'll get a firm price by text or email within 24 hours, no site visit needed for most jobs.

Get My PriceCall (920) 655-2193