What does a coated floor cost?
What does a floor coating cost per square foot, and what's included?
Ours is $6–$9 per square foot installed, with a $2,000 minimum, for garage, basement, shop and commercial floors. Patios, porches and pool decks are $7–$10, because they get a UV-stable outdoor topcoat with grit in it. That price covers diamond grinding, crack repair, the base coat, the flake and the topcoat on sound concrete. Heavy repair, grinding off an old coating or a moisture-tolerant base coat is extra, and it's priced on your quote before you decide.
What's the price for a two-car or three-car garage floor?
At $6–$9 a square foot, a 20 × 20 two-car garage (400 square feet) runs $2,400–$3,600, a 24 × 24 two-car (576) runs $3,456–$5,184, and a 24 × 36 three-car (864) runs $5,184–$7,776. Where yours lands depends on the shape the concrete is in and the finish you pick. Measure wall to wall at the floor, multiply length by width, and send that with a photo for a firm number. The cost guide has a calculator for any size.
Why is there a $2,000 minimum?
Every floor, big or small, gets the same setup and the same steps: diamond grinding with dust extraction, crack repair, a base coat, flake and a topcoat, each going down in order. On a small space like a laundry room or a mudroom the work doesn't shrink much, so those land at the minimum. A one-car garage of about 288 square feet is already above it, at $2,000–$2,592.
Why is your price higher than a cheaper quote I got?
Usually because the cheaper quote leaves something out. The common shortcuts are acid etching or a quick wash instead of diamond grinding, skipping crack repair, one thin coat instead of a real base coat, a light sprinkle of flake instead of full coverage, and a clear coat that isn't UV-stable and yellows. Ask each bidder whether they grind the whole floor, what goes down in what order, and what the written warranty covers. Those shortcuts are why so many coatings peel.
Does your system cost more than an epoxy floor?
A little, on paper. National cost guides (HomeGuide) put installed polyaspartic at about $5 to $12 per square foot and epoxy at about $4 to $10, so the gap is usually small, and ours is $6–$9 with the prep included. For that difference you park in 24 to 48 hours instead of waiting up to a week, the topcoat stays clear instead of yellowing, and the floor stands up better to hot tires.
What goes on your floor
What's actually on my floor when you're done?
Three layers on top of diamond-ground concrete. First a polyurea base coat that bonds into the opened-up surface of the slab. Then vinyl color flake, broadcast into the wet base coat until it won't hold any more, which is what full flake means. Last, a clear, UV-stable polyaspartic topcoat that locks the flake in and takes the wear. Full flake floors shows the finish up close.
Do you use polyurea or polyaspartic?
Both, and they're related: polyaspartic is a type of aliphatic polyurea. The base coat is a polyurea, there for its bond to the concrete; the topcoat is a polyaspartic, there because it stays clear in sunlight instead of yellowing. That's why you'll also see this floor called polyaspartic flake on our other pages. It's the same system.
How is a polyurea floor different from epoxy?
Epoxy is the older chemistry. It bonds and builds thickness well, but it cures slowly, so you can wait up to a week to park, and most epoxies yellow in sunlight. Our polyurea and polyaspartic system lets you walk on it within a few hours and park after about 24 to 48 hours, stays clear by a sunny door, and is tougher and more flexible under hot tires. We don't install epoxy floors; epoxy vs. polyaspartic has the full comparison.
What are the flakes, and how do I pick a color?
They're vinyl color chips, and they come in dozens of blends. Lighter blends hide dust and the white film road salt leaves behind; darker blends hide tire marks. If you want less flake, there's partial flake, a color base with a lighter scatter, or solid color with none. We bring real flake samples, because a color on a screen never matches the floor.
How we prep and install
Do you grind the floor or acid etch it?
We grind every floor, with no acid. The whole slab is diamond ground with dust extraction to about CSP 2–3 on the ICRI scale, the surface profile a broadcast coating needs to bond. Grinding cuts off the weak, chalky top layer of the slab (called laitance) along with old sealer and ground-in grime. Acid etching leaves roughly CSP 1–2, too little for a flake system to grip, and can leave residue behind. Weak prep like that is one of the most common reasons coatings peel.
How long will my garage be out of use?
Most one- and two-car garages are coated in one day. A three-car garage, a shop or a floor with an old coating to grind off can take longer, and we'll tell you up front. You can walk on it within a few hours and park after about 24 to 48 hours, depending on temperature. For comparison, an epoxy-only floor can need up to a week before the car goes back in.
My floor is cracked, pitted or painted. Can it still be coated?
Yes, that's typical. Cracks, joints and pits are cleaned out, filled and ground flush during prep, and the flake pattern hides most of what's left. Paint, old epoxy and anything peeling is ground off completely first, because a new coating is only as strong as what it's stuck to. A crack that's still moving can come back through any coating, so if we think a line could show on your floor, we'll say so from the photos.
What if moisture comes up through my slab?
It's one of the first things we look at, because water vapor pushing up through concrete is what lifts coatings off from below. Basement slabs are tested before we quote, and in a garage, signs like white powder or an old coating that's bubbling tell us to look closer. A slab with moisture coming through may need a moisture-tolerant base coat, which is priced on top; an active leak or standing water has to be fixed first. More on basement floors.
How late in the year can you coat a garage?
It depends on the garage more than the calendar. Coatings have minimum air and slab temperatures, so an attached garage can often be coated into late fall, sometimes with heat, while a cold detached garage may have to wait for spring. We check the temperatures before we put you on the schedule.
Part of my floor has sunk. What happens first?
Lift first, coat second. We do foam concrete lifting too, so a settled section of the floor, or a sunken apron at the door, gets raised back into place with polyurethane foam through small holes. The holes are patched and ground flush with the rest of the floor during prep, so the coating covers them. A coating can't make an out-of-level slab level, which is why the order matters. Garage floor leveling explains the lift.
What should I clear out before install day?
Everything sitting on the floor: cars, shelving, freezers, bikes, bins and mats. Things hung on the walls can usually stay. Light items can come back once the floor is walkable, a few hours after we finish, but heavy shelving, tool chests and anything on wheels should wait until it's ready for cars, about 24 to 48 hours. If you'd rather not move it all yourself, ask and we'll quote it.
How long it lasts
What warranty comes with a coated floor?
Every coating comes with a written warranty, spelled out on your quote before you approve it. It says what's covered in plain language, so you know before any work starts. If something isn't right later, text us a photo and we'll come take a look. Our warranty page explains how it works.
How many years should a coated floor last?
Cost guides cite 10 to 20 years or more for professionally installed polyaspartic floors in homes. Where a floor lands in that range comes down to how well it bonded, how thick the system is, how hard the floor gets used and how it's cared for. The things that cut it short are a weak bond from poor prep, moisture pushing up through the slab, and harsh solvents or abrasive pads that wear down the topcoat. A thin DIY kit is a different story.
Will hot tires pull the coating up?
Not on a properly bonded floor. Hot-tire pickup happens when a thin coating softens under a tire coming off a hot road, sticks to the rubber and lifts when you back out. It's mostly a problem with roll-on epoxy over etched concrete. Our system is bonded into ground concrete and built in layers, and a properly bonded floor like that resists hot tires, road salt, brine, oil and antifreeze.
Living with a coated floor
Is it slippery when the cars drip snowmelt?
Less than you'd expect. The flake and topcoat leave a textured surface that gives your boots something to grip, and where a floor gets wet a lot, like the strip inside the door, we can add grit to the topcoat. Any floor gets slick with ice or an oil spill on it, so wipe spills up and squeegee slush out.
How do I keep it clean, especially through a salty winter?
Sweep or shop-vac it, and mop with a pH-neutral cleaner when it needs more. In winter, salty slush sits on top instead of soaking into the concrete, so a floor squeegee pushes it out the door, and a mop now and then clears the white salt film. Skip harsh solvents and abrasive scrub pads, which dull the topcoat. Between cleanings, the flake hides a lot of dust and tire marks. More in cleaning garage and basement floors.
What happens if I drop a heavy tool on it?
Usually nothing you'll notice. A coated floor takes tool chests, floor jacks and creepers in stride. A heavy or sharp drop, or steel dragged across it, can chip or scratch any coating, though the flake pattern hides small marks well. A damaged spot can usually be repaired without redoing the whole floor, so text us a photo if it happens.
Is a DIY kit from the hardware store good enough?
For a garage that sees Wisconsin winters, usually not. Most kits are a thin epoxy rolled over acid-etched concrete with a light sprinkle of flake, and when the prep is weak, they peel, often where hot tires sit. They can look good for a while, but a thin film on a lightly etched surface doesn't have much to hold on to. Why garage floor coatings peel explains what goes wrong.
Getting started
How do I get a price for my floor?
Send photos through Get My Price or text them to (920) 655-2193: a wide shot of the floor from the door, close-ups of any cracks, damage or old coating, and the length and width. You'll get a firm price by text or email within 24 hours. We only visit when the photos can't answer something, and once you approve the price, you pick a date.
Which towns do you coat floors in?
We're based in Suamico and coat floors in Green Bay, De Pere, Suamico, Howard, Ashwaubenon, Allouez, Bellevue, Ledgeview, Hobart, Pulaski, Abrams, Oconto, Appleton, Kaukauna, Little Chute, Kimberly, Neenah, Menasha, Freedom, Wrightstown, Sturgeon Bay, Luxemburg, Kewaunee, Algoma, Shawano and Oconto Falls. Each linked town has its own page. Somewhere else in Northeast Wisconsin? Send photos with your address and we'll tell you if you're in range.
Do you coat basements, shops and patios too?
Yes. We coat basements, moisture-tested first, plus shops and pole barns, commercial floors, and patios, porches and pool decks, which get a UV-stable outdoor topcoat with grit at $7–$10 per square foot. For finishes, there's full flake, partial flake and solid color.
Can you lift sunken concrete and coat the floor in one plan?
Yes, those are the two things we do. One set of photos gets you one quote, with the lifting and the coating each priced so you can see both parts. The lift happens first and the joint at the door gets sealed, then the coating goes on the schedule, so you end up with a flush step into a finished garage. Our concrete lifting page covers that side of it.
Coating a basement floor
Do I need to empty the basement before you coat the floor?
The area being coated has to be empty: the whole floor is ground, repaired and coated in one go. Furnaces, water heaters and other fixed equipment stay; we coat around them.
Should I put carpet or a coating on my basement floor?
If the basement has ever been damp, a coating. Carpet holds moisture and odors and is ruined by a backed-up drain or a failed sump pump, while a coated floor just gets wiped dry. Carpet is softer and warmer underfoot, so plenty of people coat the whole floor and put area rugs in the family room.
Can you coat the floor in a finished basement?
Yes, as long as the floor itself is bare concrete. We grind with dust extraction and coat right up to the walls. Baseboards are best taken off before we come and put back once the coating has cured, so the coating runs underneath; if yours can't come off, tell us and we'll work along them.
Do I need to pull up old carpet or tile before you coat?
Yes, the coating has to go on bare concrete, so carpet, pad, tack strips and loose tile come up first. Old black tile adhesive is a different story: it can contain asbestos, so it gets tested before anyone disturbs it, and we don't grind it off. The floor prep guide explains the options.
Should I coat my basement floor before or after waterproofing or an egress window?
After. Interior waterproofing usually means cutting out and re-pouring a strip of floor along the walls, and an egress window brings dust and debris through the basement. Coating last means the new concrete gets ground and coated with the rest of the floor, once it has cured at least about a month and passed a moisture test.
Can you coat a basement floor that has in-floor radiant heat?
Usually, yes. Grinding takes off only the thin top layer of the slab, and a cured coating handles the warmth. Mention the heat when you send photos: we'll ask you to turn it down before the install and bring it back up slowly afterward, and if the tubing might sit close to the surface, we check before we grind.
Does a basement floor coating smell, and do we need to leave the house?
There's a noticeable smell while the coating goes down and for a while after, so we set up ventilation for the install, and it fades as the coating cures. You don't need to move out, but pets and anyone sensitive to odors are better off out of the house on install day.
How long does it take to coat a basement floor?
Usually a day, like a garage. A large basement, lots of crack repair or old paint to grind off can add time, and we'll tell you up front from your photos. You can walk on the floor within a few hours, and we'll tell you when furniture can go back.
How long does a basement floor coating last?
Many years when the slab is tested and prepped right. Cost guides cite 10 to 20 years or more for professionally installed polyaspartic floors in garages, and a basement sees no hot tires or road salt. Moisture is what shortens a basement coating's life, which is why we test first, and the written warranty on your quote spells out what's covered.
Coating a shop or pole barn floor
How long should a new pole barn slab cure before it's coated?
At least about a month. A new slab still has water working its way out, and coating it too soon traps that moisture under the coating, where it can push the coating loose. We test the slab before we coat, so if yours was poured this year, send photos and the pour date and we'll plan around it.
Can you coat a pole barn that still has a gravel or dirt floor?
No. A coating needs a concrete slab to bond to, and we don't pour concrete. Once your concrete contractor pours the slab and it has cured at least about a month, we can test it and coat it.
Can you coat a shop floor with trench drains or floor drains?
Yes. We coat to the edge of each drain so water keeps running where it should, and the grates still come out for cleaning. A coating follows the slab, though, so it won't fix water that pools away from a drain; a section that has sunk can be lifted first.
Will a coated floor crack or peel in a pole barn that freezes all winter?
Not from the cold alone. Temperature limits apply while the coating goes down and cures, not afterward, and plenty of coated detached garages in Wisconsin sit below freezing all winter. What does cause trouble in cold buildings is moisture coming up through the slab, which we check before we coat.
What happens to equipment I can't move out of the shop?
Anything bolted down, like a lift, compressor or workbench, we coat around. Everything else has to be off the area being coated, but on a big floor we can work in sections, stopping at a clean line, so equipment can sit at one end while we coat the other.
Do the saw-cut joints in my shop floor get filled or coated over?
Your choice. Control joints can be coated as a groove, which leaves room for the slab to move, or filled and coated over for a seamless look, which can show a hairline crack later where a joint moves. On a big pole barn slab with a lot of joints, we'll go over the tradeoff from your photos.
Will a coating stop concrete dust in my shop?
Yes. Bare concrete slowly wears and sheds a fine dust that settles on tools, benches and everything else, and a coating seals the surface so that stops. You'll still sweep up what comes in on boots and tires, but it sits on top where a broom or dust mop picks it up.
Can I weld or grind on a coated shop floor?
Yes, with a welding blanket or a sheet of steel on the floor under the work. Hot slag and grinder sparks can burn small marks into any floor coating, so cover the area where the sparks land.
Will jack stands and floor jacks damage a coated shop floor?
No. A coating takes jack stands, floor jacks, creepers and rolling tool chests in stride, because the weight goes through the thin coating to the concrete underneath. What scratches any coating is steel dragged across it, so set stands in place instead of sliding them.
Coating a floor in a business
Can you coat a commercial floor that has an old coating on it?
Yes, once the old coating is off. It's ground away along with the weak top layer, because a new coating is only as strong as what's under it.
Will grinding the floor make a mess in our store or office?
Some dust and a lot of noise. Our grinders run with dust extraction vacuums that capture most of the dust as we go, but merchandise and equipment near the work area should be covered or moved. The noise is one more reason most businesses book the work for a closed day.
Will a floor coating leave a lip at our doorways?
No. Each coat goes on at about 6 to 12 mils, or thousandths of an inch, so the finished floor is far thinner than the 1/4 inch the ADA allows for a vertical change in level. Where the coating stops at carpet or tile, we finish it to a clean, straight edge.
Can you coat a restroom floor in a business?
Yes, once it's down to bare concrete. A coated restroom floor has no grout lines to stain, mops clean, and gets grit in the topcoat because restroom floors get wet. We plan around toilets, partition posts and floor drains from your photos so the work fits a closed day.
Can you coat a showroom floor that vehicles drive on?
Yes. It's the same polyaspartic system we put in garages, so it's made for tires, and it gives a car, boat or powersports showroom a bright floor that cleans up with a mop. Vehicles can go back on after about 24 to 48 hours, so plan the install for a closed day or weekend with the inventory moved out.
Can we use an auto scrubber on a coated floor?
Yes, with a soft pad or brush and a pH-neutral cleaner. Skip aggressive pads, acid, vinegar or citrus cleaners, bleach and soap-based products that leave a film. Daily dust mopping does most of the work, since tracked-in grit is what wears a topcoat; more in cleaning concrete floors.
Does a coated floor need stripping and waxing like VCT?
No. The clear topcoat is the wear layer, so there's no wax to strip and reapply. Clean it with a pH-neutral cleaner, and if the traffic lanes dull after years of use, the topcoat can be scuffed and recoated without grinding the whole floor again.
How long does a coated floor last in a busy business?
It depends mostly on traffic and care. Cost guides cite 10 to 20 years or more for professionally installed polyaspartic floors in homes; a busy retail entry wears faster in its walk paths than a back room does. Walk-off mats, regular dust mopping and a fresh topcoat when the lanes dull keep it looking good longer.
Do commercial floor coatings come with a warranty?
Yes. Every coating we install comes with a written warranty, and the written warranty on your quote spells out what's covered before you approve anything. If something isn't right, text us a photo and we'll come take a look; how that works is on our warranty page.
Coating outdoor concrete
Will a patio coating turn yellow in the sun?
No. We use a UV-stable polyaspartic, which stays clear in direct sunlight. Epoxy is the coating that yellows and chalks outdoors, and that's why it doesn't belong on a patio, porch or pool deck.
Can I shovel and use ice melt on a coated porch?
Yes. A plastic shovel or one with a rubber or poly edge is easiest on it; a steel blade scraped hard or an ice chopper can scratch or chip any coating. Ice melt sits on top of the coating instead of soaking into the concrete, so sweep or rinse it off when the weather breaks.
Will pool chemicals or salt water damage a coated pool deck?
Normal splash from a chlorine or saltwater pool isn't a problem; it sits on top and rinses off. Spilled pool chemicals are different. Rinse liquid chlorine, acid or shock off right away and store them off the deck, because a strong chemical left sitting can stain or soften a coating.
Does a coated pool deck get too hot for bare feet?
A dark one can. Lighter colors stay cooler under bare feet than dark ones, so for a deck in full sun we steer you toward a light blend. Any surface in direct afternoon sun gets warm, so look at the samples outside before you pick.
Can you coat a stamped concrete patio?
We don't recommend it. A flake coating would cover the pattern you paid for. Stamped concrete usually gets a decorative sealer instead, and we do that reseal too. We can also clean it, caulk its joints, and lift it if it has sunk.
What happens to the cracks and joints when you coat a patio?
Stable cracks are filled and coated over with the rest of the patio. Joints and cracks that still move, like the gaps between slabs or where the patio meets the house, get flexible joint caulking instead, because a crack that moves can show back through any coating.
How long does it take to coat a porch or patio, and when can we use it?
Most porches and patios take a day, on a dry day. You can walk on it within a few hours, and before we start we'll tell you when the furniture, grill and planters can go back, since temperature affects the cure.
When is the best time of year to coat a patio in Wisconsin?
Late spring through early fall. The coating has minimum temperatures for the air and the slab, and an outdoor slab has to be dry when we start, so we pick a dry stretch of weather and check the slab first. Rain in the forecast moves the date.
Does a coated patio need resealing every few years?
No, not the way a sealed one does. A penetrating sealer often lasts 5 to 10 years and then gets reapplied, but a coating is the surface itself. Upkeep is sweeping, hosing it off and washing with a pH-neutral cleaner, plus rinsing ice melt off the porch in spring.
Full flake floors
Will a full flake floor hide the stains and patches on my old concrete?
Yes. With flake covering the whole floor and no base color showing, old stains, patched spots and color differences disappear. Oil that has soaked deep into the slab still has to be dealt with in prep, though, because it can keep the coating from bonding.
Is a full flake floor hard to clean with all that texture?
No. The texture is sealed under the clear topcoat, so dirt sits on top instead of working into it. Sweep or dust mop, squeegee out slush, and wash with a pH-neutral cleaner and a microfiber mop or soft deck brush. Skip abrasive pads, bleach, vinegar and citrus cleaners.
Can the texture on a full flake floor be made smoother?
Yes, within limits. The flake gives the floor its texture, and the topcoat can be adjusted: smoother for a basement you walk in socks, or with grit added where snowmelt comes in off the cars. Tell us how the floor gets used and we'll set it for that.
Will the flakes fade by a sunny garage door?
Not the way an epoxy floor does. The clear topcoat is a UV-stable polyaspartic, so it won't yellow or amber in the sun, and that yellowing is what makes older epoxy floors look faded and dingy by the door. The flake sits under that topcoat, protected from wear.
Can a chip in a full flake floor be repaired?
Yes. A chip from a dropped tool is cleaned out, filled, re-flaked and topcoated, and the busy full flake pattern hides the edges of a repair well. Text us a photo and we'll take a look.
Can a worn full flake floor be recoated instead of redone?
Usually, yes. If the topcoat dulls in the tire paths after years of use, a well-bonded floor can be cleaned, sanded and given a fresh clear topcoat without grinding off the flake. A floor that's peeling is different: it has to be ground off and redone.
Can a full flake floor really be done in one day?
Usually, for a one- or two-car garage. Grinding, repairs, the base coat, the flake broadcast, scraping and the clear topcoat all happen the same day, because polyaspartic can be recoated within hours. Bigger floors or heavy repairs can take longer, and parking waits about 24 to 48 hours.
Is full flake only for garages?
No. It's our standard for garages, and it suits shops, pole barns, entries and basements too, anywhere you want a floor that hides dust and wear and has some texture underfoot. With grit in the topcoat, it also works on porches and patios.
What does the warranty cover on a full flake floor?
The written warranty on your quote spells out what's covered, in plain language, before you approve anything. If something isn't right later, text us a photo. If it's covered, we fix it; if it isn't, we'll explain why and what the options are. More on our warranty.
Partial flake floors
What base color should I pick for a partial flake floor?
Gray is the safest pick, because it's the most forgiving with dust and scuffs. Lighter tones brighten a basement or rec room. The base color does most of the work on a partial flake floor, so choose it first, then a flake blend to go with it, using real samples in your own light.
Should the flake match the base color or contrast with it?
Either works. Flake close to the base color gives a calm, subtle look, while a contrasting blend stands out more and makes the pattern the feature. We bring samples of both so you can see them together before you choose.
Will the flake look even across a partial flake floor?
Yes. We scatter it by hand across the whole floor to the density you picked, keeping it even from wall to wall. That's harder than a full broadcast, where flake simply covers everything, so it's a fair thing to ask any installer about.
Will I see stains or patches through a partial flake floor?
Not stains. The base coat is pigmented, so what shows between the flakes is the color you picked, not the concrete. Filled cracks and patches are ground flush, but with less flake to hide them, a repair can be easier to spot than on a full flake floor, which hides small flaws best.
Does a partial flake floor show dust and footprints?
Some. The flake breaks up the surface, so it hides more than a solid color but less than full flake. A heavier scatter over a gray base hides the most; a light speckle over a dark base shows dust and footprints soonest.
Will grit change how a partial flake floor looks?
Very little. The grit goes into the clear topcoat, so you feel a fine texture more than you see it. We add it where the floor gets wet, like an entry or a laundry area, and can leave dry areas smoother.
Is a DIY flake kit the same as a partial flake floor?
It looks similar on day one, but no. Kits are a thin epoxy coat rolled over acid-etched concrete with a light sprinkle of flakes, and hot tires can lift them. Ours goes on diamond-ground concrete: a pigmented polyaspartic base, flake and a clear UV-stable topcoat, built to a real thickness.
How long does a partial flake floor take to install?
Usually a day for a garage-sized room. Grinding, repairs, the base coat, the hand-scattered flake and the clear topcoat all go on the same day, and you can walk on it within a few hours. A large basement or a floor that needs a lot of repair can take longer.
Does a partial flake floor last as long as full flake?
It depends on the room. Partial flake gets the same prep, base coat and UV-stable topcoat, so in a basement or rec room that stays fairly clean it holds up well. In a garage full of slush and salt, full flake's thicker build and busier pattern hide wear longer, which is why it's our standard there.
Solid color floors
Does adding grit make a solid color floor harder to clean?
A little. Grit gives the topcoat a fine texture that holds a bit more dirt than a smooth finish, so a soft deck brush works better than a flat mop. That's why we add it where the floor gets wet, like entries and wash areas, and can leave dry areas smoother.
Does a solid color floor show scratches?
More than a flake floor does. On one even color, a scratch from a dragged toolbox or a dropped wrench catches the light, where a flake pattern would hide it. Rubber tires, jack stands and creepers are fine; it's dragging steel across the floor that scratches it.
Can a chip in a solid color floor be touched up?
Yes, though it's easier to see than on flake. A small chip is cleaned out, filled and recoated in the same color, but on one even color the edges of a repair can still show a little. Text us a photo and we'll tell you whether a spot repair or recoating the section will look better.
How do I get tire marks and scuffs off a solid color floor?
They sit on top of the coating, so most come up with a pH-neutral cleaner and a microfiber mop or soft deck brush, and a degreaser handles stubborn tire marks. Skip abrasive pads, bleach, vinegar and citrus cleaners, which can dull the finish. More in cleaning concrete floors.
Will a solid color floor look even, or can it come out blotchy?
It should look even from wall to wall. The pigmented color goes on in more than one layer, so it builds up evenly without thin or streaky spots, and grinding the whole floor first gives every part of it the same surface to bond to.
Will a light solid color floor make my shop brighter?
Yes. A light solid color reflects more of your shop lights than bare concrete does, so the whole building looks brighter and it's easier to find small parts. The trade-off is that tire marks and scuffs show more on it than they would on a flake floor.
How long does a solid color floor take to install?
Usually a day for a one- or two-car garage or a room that size. Grinding, repairs, the color coats and the topcoat go on the same day, because polyaspartic can be recoated within hours. You can walk on it within a few hours and drive on it after about 24 to 48 hours.
Is solid color a good finish for a storage or mechanical room?
Yes. It gives a clean, bright, uniform floor that's easy to sweep and mop, and with no flake, a drip from a water heater, furnace or water softener shows up right away. Fixed equipment doesn't have to move; we coat around it.
Will filled cracks show on a solid color floor?
They can, a little. Cracks are filled and ground flush before the color goes on, but with no flake to break up the surface, a faint line can still show where a flake floor would hide it. A crack that's still moving can come back through any coating, so those get handled before we coat.
Get your floor priced from photos
Send a photo of the floor and its size. You'll get a firm price by text or email within 24 hours.
Want the full rundown first? See garage floor coatings or the coating cost guide.